-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection
The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage
220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
-7-
Replacing the Lamps
Cut off the connection of the cooker hood with electricity. Take off the aluminum cassette filter.
Take off the failed lamp and replace it with a new one that is of the same rating. (Please wait for the
lamps to cool as they might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the lamp downwards
pushing back of lamp holder downwards and then turning it a
little bit anti-clockwise take it off downwards. Figure 14
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during usage with
chimney. In order to achieve best performance, pay attention that the duct system follows the
shortest way for connection to the chimney. Your product is produced as it will be appropriate for
usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other smoke as well.
Active Carbon Filter
To provide air recirculation where product's chimney air outlet cannot be connected to exterior,
it is necessary to use active carbon filter with your product. You may purchase this accessory
from authorized sellers and after sales services
Figure 14
Replacing bulb
In order to change the bulb, turn it anti-clockwise and take it off.
Replace it with a new one in the same value by turning it in
clockwise. Figure 16
Figure 16
-10-
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection
The product has 5 speeds of ventilation level. One of 1,2,3,4,5 speeds is
selected in accordance with steam of cooking or fry. Motor is started pressing control button
on the front panel. Speed is increased pressing button, and decreased by pressing button.
Automatic timer (TIMER) is available at the models with electronic remote control. When you press
button more than 2 seconds, timer function will be on for 15 minutes. When the timer is on,
Display will signal and the motor will be off automatically 15 minutes later. Please use the cooker
and the product at the same time to enable circulation. Doing so, air suction power will be affected
positively. We recommend you to operate your product for few minutes more after the cooking is
completed to enable absorption rest of smell and steam.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when C signal appears on Display or (according to usage) each 2-3
weeks. In order to remove C signal, after the filters are cleaned and replaced to their place, press
button more than 3 seconds (when the product is at off position). Letter “E” will appear on
Display and the product will operate as normal. If you would like to continue using the product
without deleting C signal, when you press the button active speed will appear for
1 second, then C signal will appear once more and the motor will continue operating.
NOTE: C signal will appear after usage of the product for 60 hours.
TECHNICAL SPECIFICATIONS
Feeding Voltage
220-240 V 50Hz
Motor Isolation Class
Isolation Class
F
CLASS I
Replacing Lamps
Unplug power cord of your cooker hood.
1W LED LAMBA (Figure 16)
*Open the split extraction plate/glass.
*Take off the aluminium casette filter. (There are on the left and
right back edges covers which you can use for changing the
lamps on the edges. Take this covers off)
*Disconnect cables of LED lights.
*Push onto light to remove them.
*Remove tape between lamp and product body.
*Remove protective tape of new lamp before placing
Placement of remote motor (IK73 & IK74)
Remote motor power pack must be fitted with an Ikon remote motor, failure to do this will void
the warranty.
IK15 remote motor is recommended where the distance of extraction is less than 5 meters
(deduct a meter per bend)
Remote motor can be mounted up to
6
meters from the hood. It is recommended that the
motor is either insulated or mounted to reduce vibration.
-8-
Carbon Filter Usage
The product you use has 2 different carbon filter usage feature.Usage of both carbon
filters is as stated below. Cut off power of the product before you change the carbon
filter.Carbon filter should be replaced with a new one each 3-5 months because it is
used at kitchens that does not have chimney outlet.Carbon filter should never be
washed.Oil filters should be montaged on the product even though carbon filter is
used or not. Do not use your product without oil filter.
Changing Carbon Filter
2 Carbon filters should be used at the product.In order to place the carbon filter,
locating the canals on the motor cover and the canals on the carbon filter on the same
level turn it clockwise.In order to take it off, turn it anti-clockwise.
Figure 6
-9-
Usage of 3 Speed Digital Control
Peel protective papers out from the inox devices after assembly.
Speed Choice
The device has 3 degrees of ventilation. According to the cooking and frying steam, you can
choose low-middle-high ventilation levels. Buttons on the front panel are used for turning the
device on. The models with eletronic controllers have automatic timers. 15 minutes automatic
timer is turned on, when pressed any of the buttons, which starts the motor up, more than 2
seconds. When timer starts, display will signal and after 15 minutes motor will automaticly stop.
Please turn on hob and hood at the same time to activate circulation. This will provide positive
effect on vacuum power. Let the device run for a while after cooking process is finalised, thus the
remaining smell and steam will be absorbed.
2nd Speed
3rd Speed Lamp Button
Cleaning Periods of Aluminum Filter
Filter should be cleaned when “C” signal appears on the Display or each 2-3 weeks (in accordance
with the usage frequency). After cleaning and replacing filters to their places, button should be
pressed for more than 3 seconds (when the product is off) in order to remove the “C” signal. “E”
signal will appear on Display and product will start working at normal position. If you want to
continue using your product without removing “C” signal, active speed will appear for 1 second
when you press
button, then “C” signal will appear once more and the motor will continue operating.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp button in
order to start illumination.
Usage of the Control Panel
Speed Selection
You device has 3 levels of ventilation . Depending on the cooking and frying steam , you should
run the device with low- medium or high speed. To run the device , on the front panel there are
motor switch and lamp switch. Please select the desired ventilation speed.
Slider Positions
Illumination
There are two lamps and one switch that controls the illumination on the device. To turn the lamps
on please pres on to the indicated position.
0
0
(IK40 & IK41)
IK73, IK74, IK77, IK78
