IKUSI MHD-201 Programming Manual Download

Page: 10 / 14

Programming MHD-201 Modules



Channel: Enables the output channel to be selected and modified.



Frequency: Reports on the output frequency of the current radio frequency carrier and enables its value to be

modified. The frequency value must lie within the valid range for VHF and UHF bands.



Attenuation: Allows attenuation for the RF carrier signal to the output to be configured, varying this value in the

range of 0 dB to 25 dB.



COFDM mode: Allows the OFDM mode to be configured, selecting 2K and 8K values.



Bandwidth: Allows the bandwidth to be configured selecting the values 6, 7 or 8 MHz



Guard interval: allows the guard interval to be configured by selecting 1/4, 1/8, 1/16 or 1/32 symbol.



Constellation: enables the output modulation constellation to be configured by selecting from the options 16QAM

or 64QAM.



Code rate: enables the redundant encoding rate to be configured selecting the values 1/2, 2/3, 3/4, 5/6 or 7/8.

• Network:

Within this sub-data the data of the following parameters can be

configured:



Network Name: Assigns a name to the network.



Provider: Enables the name of the service provider to be specified.



NID: Enables a value to be assigned to the network identifier.



TSID: Enables a value to be assigned to the identifier of the transport stream or TS.

NOTE.
For a headend configuration with 2 or more devices, the TSID value must be different for each device.



ONID: enables a value to be assigned to the original network identifier.



NIT mode: OFF an LCN descriptor is not inserted in the NIT .



NIT LCN: Enables the LCN mode of the NIT to be selected.

Europe Mode: Europe descriptor is inserted.

Independent Television Commission: UK descriptor to be inserted.

Nordig mode V1: Descriptor is inserted according to the Nordig V1 specification.

Nordig V2 mode: Descriptor is inserted according to the Nordig V2 specification.

Generic Mode: Generic LCN descriptor.



Insert TDT-TOT: Enables information on the date and time to be inserted or not.



Name.:

Standard

2 Provider:

IKUSI

3 NID:

00001

4 TSID:

00021

5 ONID:

00100

6 NIT mode:

7 NIT LCN:

OFF

8 Ins TDT-TOT :

SEND



SEL

Summary of Contents for MHD-201















Search results

Summary of Contents for MHD-201

Reviews:

Related manuals for MHD-201

Brands by name

Popular brands

IKUSI MHD-201, Programming Manual

Search results

Summary of Contents for MHD-201

Reviews:

Related manuals for MHD-201

Brands by name

Popular brands