background image

 

 

- 31 - 

S-2018 

REV. D 

 
6.

 

Press the adapter plate assembly firmly to ensure the white 

Velcro hook adheres to the inside wall of the blower.  Then 

gently pull the blue fabric strap to pull the plate assembly out of 

the unit.  The Velcro hook (color white) should remain adhered 

to the inside of the blower. Verify that the Velcro loop strip 

(black) is still firmly attached to the back of the adaptor plate. 

 
 
 
 
 
7.

 

Set the Alkaline Battery Adaptor plate aside and use your thumbs 

to apply pressure across the Velcro hook (white) inside the 

blower to insure it is securely adhered. 

 
 
 
 
8.

 

Install five Duracell D-Cell batteries into the Alkaline 

Battery Adaptor.  (NOTE: USE ONLY DURACELL D-

CELL ALKALINE BATTERIES!) 

a.

 

Only remove and install the batteries when the 

Alkaline Battery Adaptor Plate is removed from 

the blower.

 

b.

 

Be sure to pay attention to the polarity (+ or -) 

direction engraved into the back plate to insure 

correct battery orientation.  This is very important to 

ensure the blower operates properly. 

 
 
 
 
 
 

 

 

 

 

 

 

 

Velcro Loop on Back of 

Adaptor Plate 

Alkaline Pack 

with Batteries 

Installed

 

Summary of Contents for S-5000 Series









































Reviews: