background image

 

 

 

During Operation 

 

 

The  machine  must  be  stopped  in  case  of  an  abnormal  voice  is  heard  while  running  of  the 

machine. 

 

The tractor must be set into motion by softly clutching. Sudden and strong movements may 

cause  dangerous  jumping  up  and  rearing  up  especially  while  going  upwards  and  pulling 
loads. 

 

One or a few passenger  never being carried during the tractor in  motion except  the person 

who drives the tractor unless the tractor sitting areas are equipped properly. 

 

Never try to run the tractor or execute maneuvers before the driver sits its chair. 

 

Never permit anybody to climb on the machine during operation in the field as well as going 

and coming back from the field.  

 

Comply  with  required  traffic  rules;  take  safety  measures  when  you  go  to  traffic  with  your 

tractor  mounted  with  the  machine.  Completely  comply  with  instructions  for  protecting 
against accidents and safely usage.  

 

Moving and turning parts never handled.  

 

Before handling the machinery components, wait them until stop entirely. 

 

Do not enter between the tractor and the machine while the tractor operating unless the park 

brake engaged and the wheels hindered with wedges.  

 

Never  put  weights  on,  never  permit  people  climb  on,  never  insert  your  hands  into  the 

machine during operation. 

 

Never leave the driver sitting area if the tractor is running. 

 

Be careful of the danger of overthrowing while working in sloping fields.  

 

Shouldn’t go backwards during the operation. 

 

Never approach the machine, never let people to approach the machine during the operation 

 

Proper plowing must be performed against the danger of erosion. 

 

During  operation,  never  insert  your  arms  and  feet  between  the  tractor  and  the  machine  or 

never hold the machine. 

 

After finishing of the operation 

 

 

Before leaving the tractor, take down the machine mounted on the hydraulic. Apply parking 

brake, take the engine key after turning off the engine. 

 

Ensure  that  it  must  be  taken  down  the  ground  completely  before  leaving  the  equipment 

mounted on rear side of the tractor at the end of the operation. 

 

If it is possible, the tractor must be parked on a smooth place and in this position be shifted 

in  any  of  the  gears  and  be  applied  the  park  brake.  If  it  is  to  be  parked  on  a  sloping  field, 
must be shifted in 1. Gear for uphill, rear gear for downhill and park brake must be applied 
for both of these situations.  

 

The machine must be kept clean against the danger of fire. 

 

The machine will be ready for operation after equipped with all protective systems and taken 

into safety condition. 

 

Never stand within the turning and swaying area of the machine. 

 

Never climb on; never crawl under the machine while the machine mounted on the tractor. 

Because the machine can bring down at any moment and severe injuries may occur. 

 

The hydraulic system must be in neutral position while leaving the tractor. 

 
 
 
 

Summary of Contents for TXS 20































Reviews: