4-1
P71D0DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
CAUTION!
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
2. Disassembly Method
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the
Table."
Reference Notes in the Table
1. Removal of the Rear Cabinet: Remove screws
9(S-1), 4(S-2) and (S-3) then slide the Rear
Cabinet backward.
2. Removal of the CRT CBA: Disconnect CN1501
then pull the CRT CBA backward.
3. Removal of the Main CBA:
CAUTION:
Discharge the Anode Lead of the CRT
with the CRT Ground Wire before removing the
Anode Cap.
Disconnect CN801, CN802, CN571 and CN691 on
the Main CBA and remove Anode Cap. Then slide
the Main CBA backward.
4. Removal of the DTV Module CBA Unit: Remove
Module PCB Holder and disconnect CN901 and
CN902 on the DTV Module CBA Unit.
5. Removal of the CRT: Remove screws 4(S-4).
Then slide the CRT backward.
Step/
Loc.
No.
Part
Removal
Fig.
No.
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
Note
[1]
Rear
Cabinet
D1
D2
9(S-1), 4(S-2), (S-3)
1
[2]
CRT CBA
D4
D5
CN1501
2
[3]
Main CBA
D3
D4
D5
CN801, CN802,
CN571, CN691,
Anode Cap
3
[4]
DTV
Module
CBA
Unit
D3
D5
CN901, CN902,
Module PCB Holder
4
[5]
CRT
D4 4(S-4)
5
↓
(1)
↓
(2)
↓
(3)
↓
(4)
↓
(5)
[1] Rear Cabinet
[2] CRT CBA
[3] Main CBA
[4] DTV Module
CBA Unit
[5] CRT
Summary of Contents for CR320IL8 A
