background image

Ilumen 

 

18

 

Installation Manual Ilumen PIDbox Light v1.2 

10

 

T

ROUBLESHOOTING

 

10.1

 

F

AULTS

 

LED readout 

Fault 

Corrective action 

No leds visible 

Product does not work 

Make sure the DC-power supply is 

plugged into a AC-outlet. Also make 
sure the outlet is under tension. 

No leds visible 

Product does work and 
makes some clicking 

noises 

This can happen at dusk and dawn. LED 
should light up after a while. If not 

please contact iLumen technical 
service. 

Led gives other color 
than BLUE, GREEN, 

WHITE, CYAN, 
PURPLE or RED 

Product does not work 

Please contact iLumen technical 
service. 

No RED or PURPLE 

led during nighttime 

while during the day 
blue led is burning 

Curing of the panels is not 

working 

This can have 2 reasons: 

 

PID is not present on PV-

modules (however the first 

night of regeneration the led 

must be on). 

 

Earth connection between 

PIDbox Light and the frame of 
the modules is interrupted 

Red led blinking 

during the night 

Product does not work 

If you connected the PIDbox when it 

was already dark outside, the PIDbox 

will not become active during that 1

st

 

night. Normally the PIDbox Light 

should work the nights after that when 
the solar plant has been active during 

the day.

 

10.2

 

N

O GOOD 

PID

 REGENERATION

 

If the modules are not regenerating or not regenerating fast enough you should check following 
things: 

 

Check the grounding of the system. If necessary you should place additional 
interconnections between the frames of the modules. 

 

Is the Ilumen PIDbox Light properly connected to the grid? 

 

Is the DC power supply properly connected (is its indication light burning)? 

 

Let an expert check if the problem you

’re

 having with the yield is caused by PID 

10.3

 

R

ESETTING THE 

PID

BOX 

L

IGHT

 

The PIDbox Light can simply be reset by unplugging the DC-power cable. Wait 10 seconds and 
connect the DC-power cable back to the PIDbox Light. 
 
If resetting does not help fixing your problem, please consult chapter 10.1 of this manual. 

10.4

 

R

EPAIRING THE 

PID

BOX 

L

IGHT

 

Do not try to open up the PIDbox Light by yourself. This will void the warranty 

Summary of Contents for PIDBOX





















Reviews: