background image

7

EXTRACTOR HOOD

Dear Customer,
Thank you for buying our hood. Please read these instructions carefully 

for its optimum installation, use and maintenance.

Notes

: The figures mentioned in this manual are in the first pages.

This hood is designed for fitting in a cabinet or on some other support.

Warning:

 consult local regulations regarding fumes outlets. Do not 

connect the hood to a fume, ventilation or hot air duct. Confirm 

that  room  ventilation  is  appropriate  with  the  local  authorities. 

Make sure

the  maximum  air  extraction  flow  rate  for  the  appliances  in  the  room 

does  not  exceed  4  Pa  (0.04  mbar).The  room  must  have  adequate 

ventilation if an extractor hood is used simultaneously with appliances 

that  run  on  gas  or  other  fuels.  The  evacuated  air  must  be  extracted 

through ducts that are used for evacuating fumes from appliances that 

run on gas or other fuels. Regulations regarding air extraction must be 

complied with.
This product in intended for HOUSEHOLD USE only.
Use a rigid PVC pipe with a min. Ø l20 mm to evacuate fumes outside.
The  above  restrictions  do  not  apply  to  hoods  with  no  fumes  outlet  to 

outside

(recirculation system with activated charcoal filter).

Install the hood in line with the instructions on the template 

  

Install   the hood  in  line  with  the  instructions  on  the  template 

provided.

For  gas  cooking  appliances  only:  the  minimum  distance  to  the  hood 

must be  at least 65 cm.

INSTALLATION

The cooker hood is supplied with

 

1 Spacer (F)

 

4 Screws

 

2 Bulbs

Close  the  space  that  remains  between  the  hood  and  the  wall, 

adjunsting the spacer (F).
Before  completing  any  connection,  make  sure  the  house  voltage 

corresponds with the voltage indicate on the data label.

Connecting the hood to the grid

Warning:

  before  connecting  the  hood:  switch  off  the  electricity 

supply  and  check  that  the  supplied  voltage  and  frequency 

coincide with that indicated on the appliance nameplate.

If  the extractor hood has a plug, connect it to a power socket in line 

with applicable regulations, located in an accessible area.
If  the hood does not have a plug, connect it directly to the electrical 

grid, protected by a separator device accessible for disconnection, in 

line with local regulations.
The connection to the electrical mains must be made as follows:

BLUE………………………..”N” NEUTRAL
BROWN……………………..”L” LIVE
GREEN AND YELLOW……(simbolo tierra) EARTH

If  the  terminals  of  the  plug  are  unmarked  or  if  you  are  in  any  doubt 

consult a qualified electrician.
If it is not supplied fit a plug normalized in the cord for the load showed 

on the rating plate.

USE OF THE HOOD – SAFETY

Warning: 

the  hood  may  stop  working  during  an  electrostatic 

discharge (e. g. lightning). This involves no risk of damage. Switch 

off  the  electricity  supply  to  the  hood  and  reconnect  after  one 

minute.
Do not allow the hood to be used by children or persons with reduced 

(physical,  sensory  or  mental)  capabilities  or  lack  of  experience  and 

knowledge, unless they have been given instruction concerning use of 

the appliance by a person responsible for their safety.
Children  should  be  supervised  so  that  they  do  not  play  with  the 

appliance.

To    avoid  the  risk  of  fire,  clean  the  metal  filter  regularly,  permanently 

control  pans  containing  hot  oil  and  do  not  flambé  food  underneath 

the hood.
Do  not  use  the  hood  if  it  shows  signs  of  damage  or  imperfection. 

Contact an official distributor or authorised dealer.

Accessible parts may heat up when using cooking appliances.

OPERATION INSTRUCTION

SWITCH ON THE LAMPS 

(C-1, FIG.2)

• Pull out the grill (G) more than 50 mm,
• Slide the switch (C-1) from position *0” to “1”.
• ASPIRATE SPEED (FIG.2)
• Pull out the grill (G) more than 50 mm
• Slide the switch (C-2) from position “0” to “1” allow speed.
• Adjust the aspirate speed at mid speed by Slide the switch (C-3) from 

position “ 1” to “2”
• Adjust the aspirate speed at high speed by Slide the switch (C-3) form 

position “2” to “3”
• Switch off the appliance by slide  the switch (C-2) from position “1” 

to “0”
• LED (C-4) will be lighted up when the aspirate motor operate. 

YOU CAN CHANGE THE SPEED DURING OPERATION.

SUCTION VERSION

If the hood is to be installed as a SUCTION hood, connect the plastic 

outlet  piece  (A)  supplied  with  the  hood  (125mm  diameter  pipe  for 

better performance and lower noise levels.

FILTERING VERSION (INTERNAL RE-CYCLING)

When  there  is  no  exhaust  duct  for  venting  out-door,  you  can  use  a 

carbon filter (D). The air is depurate by the filter and put again in the 

surrounding.
The air is released in the room through a connecting pipe, which goes 

through the hanging cupboard and us connected to the connecting 

ring supplied (A) Fig 1.

To use the appliance in this version, proceed as follows:

 

Open the grids (E)

 

To proceed to change the charcoal filter (D).

 

Reinstall the grids.

HOOD MAINTENANCE

Warning:

 always switch off the electricity supply before carrying 

out  maintenance  work  on  the  hood.  In  the  event  of  a  fault, 

contact an official distributor or authorised dealer.

Exterior cleaning: use non-corrosive, liquid detergent and avoid the use 

of abrasive cleaning products.

Grease filters: to avoid fires, clean thoroughly once a month or whenever 

the display pilot light indicates as such. To do so, remove the filters and 

wash with hot water and detergent. If using a dishwasher, position the 

filters vertically to prevent solid remains from depositing on them.
Activated charcoal filters: replace the every 2 months.

Important:

  increase  the  filter  cleaning/replacement  frequency  if 

the hood is used for more than 2 hours a day. Always use genuine 

filters from the manufacturer.

Bulb replacement (look for the 

symbol in the figures)

Warning:

 do not handle the bulbs until the electricity supply has 

been switched off and they have cooled.

Important:

 use new bulbs according to that indicated on the hood 

nameplate.

Use  bulbs with an aluminium reflector to replace halogen bulbs. Do not 

use dichroic bulbs - risk of overheating.

On cooker hoods equipped with tungsten lamps, the lights should only be used 

during  operation  of  the  motor.  They  should  not  be  left  on  permanently  and 
used as a light source.

Legal information

The manufacturer:
- Declares that this product meets all basic requirements regarding low-

voltage  electrical  equipment  established  in  Directive  2006/95/EC  of 

12  December  2006  and  electro-magnetic  compatibility  established  in 

Directive 2004/108/EC of 15 December 2004.

-  Is  not  responsible  for  any  failure  to  observe  the  instructions  given  in 

this  manual  and  current  safety  regulations  for  the  correct  use  of  the 

equipment.

- Reserves the right to make any modifications to the equipment or this 

manual without prior notice.

Contact  our official distributor should you require technical assistance 

or additional information on our products.

EN

Summary of Contents for CSFR60








Reviews: