Image Engineering iQ-Near Focus User Manual Download | Manualshive

Page: 10 / 12

background image

Image Engineering

Seite

10

von

12

-

Secure the upper frame with one hand on either

side.

-

Loosen the highlighted handles by turning them

counterclockwise

-

Lift or lower the frame to the desired height

-

Tighten the handles down again firmly to prevent

the frame from dropping on its own.

WARNING:

Risk of pinching!

Figure 6: Height adjustment of iQ-Near Focus

«
...
8
9
10
11
12
»

Summary of Contents for iQ-Near Focus













Reviews:

No comments

Related manuals for iQ-Near Focus

Brand: 3M Pages: 26

Brand: NEC Pages: 144

BOS R254K-UUI-LH10-S4

Brand: Balluff Pages: 196

Brand: VEAP SHIELD UNITED Pages: 3

Brand: FALEEMI Pages: 12

Brand: iDataLink Pages: 30

Brand: jbc Pages: 4

Brand: jbc Pages: 4

Brand: jbc Pages: 8

Brand: Lanier Pages: 3

Brand: Sami Pages: 10

Brand: Warmup Pages: 4

Brand: Saab Pages: 10

Brand: S/C Black Pages: 34

AERASGARD RCO2-W

Brand: S+S Regeltechnik Pages: 7

Brand: Insignia Pages: 2

Brand: PolyScience Pages: 14

Brand: Thermador Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands