background image

8

6.

Have a second person hold the Top Crossbar (48) so
that the pull-up bar faces away from the rack, as
shown.

Attach the Top Crossbar (48) to the left Upright (43)
with two M10 x 70mm Bolts (21), a Small Support
Plate (51), and two M10 Nylon Locknuts (11). 

Do not

tighten the Nylon Locknuts yet.

Attach the Top Crossbar (48) to the right Upright (43)
with two M10 x 70mm Bolts (21), a Small Support
Plate (51), and two M10 Nylon Locknuts (11). 

Do not

tighten the Nylon Locknuts yet.

6

21

51

21  

11

11

11

48

11

Pull-up

Bar

51

21

21

43

43

7.

Press a 25mm Bushing (73) into each end of the
Locking Bar (62).

Insert the Barbell (63) through the Locking Bar (62)
until the Barbell is centered in the Locking Bar.

63

73

62

73

7

8.

Identify the Left Weight Glider (60) by looking at the
position of the round tube.

Press a 38mm Bushing (58) into each end of the
round tube on the Left Weight Glider (60). 

Slide the Left Weight Glider (60) onto the left end of
the Barbell (63). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 16mm Bolt (75).

Look at the drawing on page 4 to make sure that
you have correctly identified the left end. The Left
Weight Glider must be turned as shown in the
drawing.

Repeat this step with the Right Weight Glider (not
shown).

75

60

58

63

Round tube

58

8

Summary of Contents for Image 4.5




















Reviews: