background image

9

5. Make sure that a qualified electrician has wired the

spa to a 240 volt power source.

Remove the two warning decals (see page 5) from

the spa shell. Using a damp cloth, wipe the spa shell

clean.

Before filling the spa, make sure that it is

in the desired position and that there is room to

easily service it. Once the spa is filled, it will

have to be drained before it can be moved.

Using a garden hose or other clean water source, fill

the spa.

Do not use soft water.

The spa may be

filled with cold water; however, if warm or hot water

is used, the spa will be ready for use sooner. Fill the

spa until the water is at the middle of the skimmer

(not shown).

Do not overfill the spa.

Refer to the inset drawing. Set the Filter (5), Filter

Plug (16), Diverter (21), and Basket (22) into the fil-

ter housing. Next, screw the Filter Cover (3) into the

filter housing until it is fully seated.

3. Insert the pillow (47) into the lounge seat recepta-

cle. The pillow can be rotated 180º to change

between the high or low positions.

4. The hydrotherapy spa operates on a 240 volt power source and must be wired directly to a 240 volt Ground

Fault Circuit Interrupter (GFCI) installed in your home.

This procedure must be performed by a qualified,

licensed electrician. A wiring diagram is found on the inside of the electronics package for reference.

Under no circumstances should the spa be wired by someone other than a qualified electrician.

Before

you have the spa wired, make sure it is in the desired position, and that it can be easily serviced, if needed.

6. Pull down one of the straps on the Spa Cover (11)

and hold the Buckle (26) against one of the panels

on the spa. (Note: To position the Buckle correctly,

have a second person hold the strap on the opposite

side of the Spa Cover snug.)

The Spa Cover must

be snug. Do not place the Buckle over the

grooves between the premium cedar panels.

Refer to the inset drawing. Remove the latch from

the Buckle (26). Attach the Buckle to the panel with

two #4 x 3/4” Screws (27).

Attach the other three Buckles (26) to the panels in

the same way.

Remove the Spa Cover (11) from the spa.

5

Fill to here

Garden

Hose

6

11

26

Strap

Strap

Latch

26

27

3

22

21

16

5

47

3

Summary of Contents for IMSB73920





















Reviews: