background image

9

5. Attach the nozzle on the air pump to the valve on

the floor of the Inflatable Liner (29). Use the air
pump to fill the bottom of the Inflatable Liner with air.

Be extremely careful not to puncture the Liner.
You will need to operate the pump by hand for
this step.

Next, attach the nozzle on the air pump to the valve
on the bolster of the Inflatable Liner (29). Fill the bol-
ster until there are no wrinkles.

6. Before filling the RENEW 815 with water, make sure

that the spa is in the desired location, that it can
easily be serviced, and that the cover can easily be
removed. Once the spa is filled, it will have to be
drained before it can be moved. 

Using a garden hose or other clean water source, fill
the RENEW 815 until there are 2 to 3 inches of
water in the spa. 

Next, smooth out the wrinkles in

the sides and bottom of the Inflatable Liner (29).
Although a few wrinkles are normal, it is very
important to smooth out as many wrinkles as
possible. 

Resume filling the spa until the water

reaches the fill line. 

Do not overfill the spa. 

Note:

When the spa is filled, the Spa Surround (9) may
bow slightly; this is a normal condition.

After the spa is filled, the spa jet unit must be
primed before the spa is used (see PRIMING THE
SPA JET UNIT on page 10). Important: Prime the
spa jet unit before continuing to step 7. 

7. Use the air pump to fill both chambers of the

Inflatable Cover (4) with air. 

Slide one of the four straps inside the Spa Cover
(11) through one of the loops on the Inflatable Cover
(4). Attach the latch on the strap to the buckle on the
other end of the strap. Attach the other three straps
to the loops on the Inflatable Cover in the same way. 

8. Place the Spa Cover (11) over the spa and line up

the bulge on the Spa Cover with the console on the
dry side jet pack. Snap each of the six latches on the
Spa Cover into the buckles on the Spa Surround (9).

7

8

6

5

Fill Line

Air Valve

Air Valve

Air Valve

Bulge

Console

Buckle

Latch

4

11

11

9

29

29

9

Pouch for

Jet Plugs

Latches 

and Buckles

Summary of Contents for 815inflatable




















Reviews: