background image

A. The filter can be removed for cleaning or replace-

ment (see CHECKING AND CLEANING THE FILTER
CARTRIDGE on page 13).

B. The underwater light can be used for night opera-

tion (see USING THE CONTROLS on page 12). The
spa includes both red and blue covers for the light. 

C. The temperature probe monitors water temperature.

D. The volcano jet provides a soothing foot massage.

E. The whirlpool jet diverts the water flow four ways.

Turn the outer ring clockwise or counterclockwise
until the ring stops and you hear a click. With each
click, the water flow is diverted as follows: to seat 3,
and the jet labeled D; next, to the seats labeled 1, 4,
5, and 6; next, to the whirlpool jet; and then to all
the jets and seats. Note: The outer ring may be
hard to turn while the pump is turned on high.

F. The two suction covers provide water to the pump.

Never operate the spa without the suction covers in
place over the fittings.

G. The ozone jet provides ozone sanitation to the spa.

The ozone generator engages during the spa’s filtra-
tion cycles to destroy algae, viruses, and bacteria
while breaking down chemicals and solids for easy
removal by the filtration system. Ozone oxidizes com-
bined chlorine and bromine, freeing them to be con-
tinuously re-used, reducing the chemical needs and
costs of the spa’s sanitation.

H. The console controls the spa jets, turns the underwa-

ter light on and off, and adjusts the water temperature
setting (see USING THE CONTROLS on page 12).

I. The three air controls regulate the air flow to the

hydrotherapy jets.

J. The four neck jets can be adjusted to spray soothing

water on your neck.

K. The nine rotary jets provide a spinning massage.

L. The six dual rotary jets provide a pulsating mas-

sage action. Rotate the outer ring counterclockwise to
turn the jets on. Rotate the outer ring clockwise to
turn the jets off. The jets labeled L1 are always on
regardless of the position of the whirlpool jet (E).

M. The two power massage jets provides a soothing

massage to your lower back. Turn the outer ring to
regulate the flow.

N. The four adjustable, directional jets can be pivoted

to direct their water flow. To open the jets, turn the
outer rings counterclockwise; to close the jets, turn the
outer rings clockwise. If no air flows through the jets,
turn the jets counterclockwise. Close the jets to
increase the water pressure to other jets. 

O. The skimmer cleans the surface of the water.

11

Spa Shell Diagram

A

O

B

D

I

Seat 1

Seat 2 

Seat 3 

Seat 4 

Seat 5 

Seat 6 

E

H

F

F

N

N

J

L1

M

N

N

L1

K

K

J

K

K

C

L1

L

L

L

G

Summary of Contents for IMSB62820





















Reviews: