background image

7

There are many factors to consider when choosing a location to set up the hydrotherapy spa. These factors vary

depending on whether you plan to use the spa inside or outside. We have listed several factors you may wish to

consider as you decide where to set up the spa.

If you set up the hydrotherapy spa inside:

1. The spa will increase the level of humidity in your

home. The location you choose should be well

ventilated. You may need to install a ventilation fan

or use a dehumidifier.

2. The spa should be located near a 240-volt power

source. It must be wired directly into a grounded

circuit with a Ground Fault Circuit Interrupter

(GFCI) capable of carrying 30 amps. No other

appliance should be on the same circuit.

3. The spa should be close to a source of water.

4. Do not use the spa on carpet or other material that

may be damaged by moisture. We recommend

that you place the spa on a water- and stain-resis-

tant, non-slip surface with a floor drain for any

water that may splash from the spa.

5. Be sure that the location you choose is stable. It

must be able to support the weight of the spa

when it is filled with water, plus the weight of the

occupants. The spa weighs approximately 2,900

pounds when it is filled with water.

6. Do not use the spa above a finished living area,

due to the risk of water damage.

7. Be sure that there is room around the spa to per-

mit servicing of the unit. The dimensions of the spa

are 84” W x 84” L x 36” H. You should allow for this

size when choosing the location.

8. The spa is not designed for in-floor installation.

However, it is compatible with a deck system that

is built flush with the top of the spa, provided you

leave access to the motor for service.

9. Be sure to note any other considerations, such as

aesthetics or privacy concerns, that may affect the

safety or enjoyment of using the spa.

If you set up the hydrotherapy spa outside:

1. Check local building codes concerning the use of

outdoor spas.

2. The spa should be located near a 240-volt power

source. It must be wired directly into a grounded

circuit with a Ground Fault Circuit Interrupter

(GFCI) capable of carrying 30 amps. No other

appliance should be on the same circuit.

3. The spa should be close to a source of water.

4. We recommend that you place the spa on a water-

and stain-resistant, non-slip surface. Do not use

the spa on rough or sharp surfaces such as gravel

or wood chips.

5. Be sure that the location you choose is stable. It

must be able to support the weight of the spa

when it is filled with water, plus the weight of the

occupants. The spa weighs approximately 2,900

pounds when it is filled with water.

6. Consider environmental factors such as rain, wind,

shade, sunlight, and so forth.

7. You should be able to monitor the use of the spa

from your home, to prevent unauthorized use by

children. You may want to enclose the spa with a

fence and self-latching gate to prevent unautho-

rized use.

8. Be sure that there is room around the spa to per-

mit servicing of the unit. The dimensions of the spa

are 84” W x 84” L x 36” H. You should allow for this

size when choosing the location.

9. The spa is not designed to be installed below

ground level. However, it is compatible with a deck

system that is built flush with the top of the spa,

provided you leave access to the motor for ser-

vice.

10.Be sure to note any other considerations, such as

aesthetics or privacy concerns, that may affect the

safety or enjoyment of using the spa.

Choosing a Location for the Hydrotherapy Spa

Summary of Contents for IMSG62820





















Reviews: