background image

17

ATTACHING AND REMOVING THE ACCESS PANEL

Turn off the spa power. To remove the indicated

Access Panel (25), remove the eight #10 x 2”

Machine Screws (37) that secure the Access Panel to

the spa. Carefully remove the Access Panel and set it

aside.

To replace the Access Panel (25), hold the Access

Panel in place and secure it with the eight #10 x 2”

Machine Screws (37).

Be careful not to overtighten

the Screws.

DRAINING THE HYDROTHERAPY SPA

The hydrotherapy spa should be drained at least four

times per year and refilled with clean water. You may

need to drain the spa more often, depending on the

user load. This must be done because after repeated

chemical treatment the water becomes chemically

saturated. Once this happens, additional chemical

treatment of the water is no longer effective. The spa

should also be drained if you will not be using it for

long periods of time. The spa must always be drained

before major repairs are made.

The hydrotherapy spa should always be covered

when it is empty. Direct sunlight can cause exten-

sive damage. The surface of the spa shell can

reach temperatures as high as 150°F in a matter

of minutes if exposed to the sun while it is empty.

These high temperatures can cause significant

damage, such as blistering of the shell surface

and warping of the spa shell. Any damage caused

by sun exposure is not covered under warranty.

To drain the hydrotherapy spa, follow the steps below:

1. Using the console, adjust the temperature to the

lowest setting.

2. Shut off the power to the spa, at the circuit break-

er or GFCI.

3. Remove the access panel from the spa (see

ATTACHING AND REMOVING THE ACCESS

PANEL on this page).

4. Pull the drain hose out and hold it above the

waterline. Remove the cap, open the valve knob,

and attach a garden hose to the drain hose. Lower

the drain hose and drain the spa.

5. When the spa is empty, remove the garden hose,

close the valve knob, and reattach the cap and

return the drain hose inside the spa.

6. Reattach the access panel.

7. Refill the spa and treat the water with chemicals

(see pages 11 and 16).

25

37

37

Drain

Hose

Valve

Knob

Cap

Summary of Contents for PARADISE IMSB53940

























Reviews: