background image

MR60 – GLASS FROSTER

 

 

 

 
WARRANTY 

 
These Glass Froster

’s are guaranteed by IMC for 2 years from the date of 

purchase from IMC, or from one of its stockists, dealers or distributors. The 
guarantee is limited to the replacement of faulty parts or products and excludes 
any consequential loss or expense incurred by the purchaser. Defects which 
arise from faulty installation, inadequate maintenance, incorrect use, connection 
to the wrong electricity supply, or fair wear and tear, are not covered by the 
guarantee. 
 
The guarantee applies in this form to installations within the United Kingdom. 
Export units carry 2 years 

“parts only” warranty. 

 
Please observe these instructions carefully. 
 

DELIVERY 

 

The packaged machine consists of: 
 

MR60 Glass Froster containing: 

           Shelf (Full size) 

           Shelf (base ½ size) 

           Shelf clips 

Sets of keys 

 

Instruction Booklet 

 
 
Please notify both the carrier and the supplier 

within three days

 of receipt if 

anything is missing or damaged. 
 
Check that the correct machine has been supplied and that the voltage, marked 
on the rating plate, is suitable for the supply available. The rating plate is 
located internally on the right hand side of the unit. 

Summary of Contents for MR60






















Reviews: