background image

 

ATTENTION!

DO  NOT  hose  or  pressure  clean this  appliance.  It  is  vital to follow  the  cleaning  procedures 

detailed later in section 7 of this manual

 

4.2. SAFETY INSTRUCTIONS     

A FULLY TRAINED AND COMPETENT PERSON MUST ONLY USE THE ATTACHMENT AND/OR MIXER.   
When manoeuvring or lifting a bowl and contents with a total weight in excess of 500kg a bowl truck must be used. 
Avoid tasks concerned with manual handling that involves a risk to health as far as reasonably possible. This 
equipment should only be stored in or transported through an environment with an ambient temperature above 5°C 
and less than 55°C.   

Note: The mixer must only be used for the purpose it was design and inline with the supplied operating instructions. 
When mixing ingredients care must be taken to avoid the inhalation of dust particles e.g. flour. Reference should be made 
to product supplier's data sheets to ensure adequate precautions and protections are taken 
The following instructions must be observed when operating the mixer 
 

4.3. NEVER   

 

Never    Change speed whilst the mixer is operating.   

 

Never    Wear loose clothing that may become caught in the mixer whilst it is in operation.   

 

Never    Attempt to reach into the bowl whilst it is mixing.   

 

Never    Leave the gear lever in mid position.   

 

Never    Use the bowl lift handle to stop machine.   

 

Never    Use the gear lever to stop the machine.   

 

Never    Access rotating parts.   

 

Never    Use excessive force when operating which could affect the stability of the mixer.   

 

Never    Operate the mixer if parts are disassembled. 

 

Never    Fit the agitator to the mixer without a bowl in place.   

 

Never    Leave the agitator on the machine without the bowl being fitted.   

 

Never    Operate the mixer with both attachment and agitator fitted.   

 

Never    Override the safety switches fitted to the mixer.   

 

Never    Open the guard to stop machine.   

 

Never    Use the mixer in an unsafe condition.   

 

Never    Operate the mixer or attachment if a fault develops or the mixer is unsafe.   

 

Never    Attempt to repair the appliance. A qualified technician must service the machine.   

 

Never    Clean the mixer with scouring powder or a scouring pad. 

 

Never    Clean aluminium agitators in a dishwasher.   

 

Never    Inhale mixing ingredient dust particles. 

4.4. ALWAYS 

 

Use the mixer as intended and inline with the operating instructions.   

 

Use the mixer in a well-lit area.   

 

Ensure the bowl, agitator, attachment and guard are correctly fitted to the mixer. 

 

Remove the agitator before using any attachments.   

 

Stop the mixer before adding more ingredients.   

 

Use the stop button to stop machine.   

 

Disconnect the mains electricity supply before cleaning the mixer.   

 

Clean the bowl, agitators and attachments after use.   

 

Clean the mixer using mild soap and water.   

 

Clean the mixer daily.   

 

Inspect the power cable and appliance regularly. If a fault is found do not operate.   

 

Disconnect the mains electricity supply before cleaning the mixer.   
 

Summary of Contents for B10



















Reviews: