Audio Player Module
These instructions are intended for users
without any specific technical knowledge.
Please read these operating instructions care-
fully prior to operation and keep them for later
reference.
1 Applications
The audio player module DMP-30 is designed for
installation into an existing unit, but it can also be
used as a stand-alone unit. For operation, it re -
quires a 12 V DC voltage.
The audio player is able to replay audio files
in the formats MP3, WAV and WMA from, for
example,
– USB flash drives (64 GB max.)
– USB hard disks
(with separate power supply, if required)
– memory cards (64 GB max.)
– mobile devices
with “Android” operating system
Note: Due to the large number of storage device manu-
facturers and device drivers, it cannot be guaranteed that
all storage media are compatible with the DMP-30.
2 Important Notes
This module corresponds to all relevant directives
of the EU and is therefore marked with
.
G
The module is suitable for indoor use only. Pro-
tect it against dripping water and splash water,
high air humidity and heat (admissible ambient
temperature range: 0 – 40 °C).
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
G
No guarantee claims for the module and no lia-
bility for any resulting personal damage or mate-
rial damage will be accepted if the module is
used for other purposes than originally intended,
if it is not correctly connected or operated, or if it
is not repaired in an expert way.
3 Installation and Connection
1) To install the module into a unit, a cutout of
156 mm × 50 mm mm is required. The installa-
tion depth is 90 mm, without taking into account
the connection jacks and plugs. Push the mod-
ule into the cutout and fasten it via its front panel
using four screws.
2) Connect the RCA jacks OUTPUT on the rear to
the line signal input of an audio unit (amplifier,
active speaker system, mixer etc.).
3) For power supply, feed 12 V to the low-voltage
jack. The current consumption is 120 mA*. For
connection, a low-voltage plug 5.5
/
2.1 mm
(outside/
inside diameter) is required. Always
observe the correct polarity (centre contact =
positive pole). Use, for example, the power sup-
ply unit PSS-1205DC from MONACOR.
* If a hard disk without separate power supply unit is
connected, its current consumption must be added to
this value.
4 Remote Control
1) To insert the batteries (2 × 1.5 V, size AAA),
remove the battery compartment cover on the
rear of the remote control. Insert the batteries
as indicated in the compartment, and then close
the cover.
If the remote control is not in use for a longer
period of time, always remove the batteries to
prevent damage due to battery leakage.
2) When you press a button on the remote control,
always point the remote control at the audio
player. Make sure that there are no obstacles
between the remote control and the player.
3) If the operating range of the remote control
decreases, the batteries are discharged and
must be replaced.
5 Operation
Connect, for example, a USB flash drive or a hard
disk (with separate power supply, if required) to the
USB port
and / or insert a memory card into the
slot SD/ SDHC / MMC (notched corner to the right
and facing the player). To remove the card, push
the card into the slot until it disengages.
All control options can be found in the table on the
right.
Notes
1. When the sliding switch PLAY MODE on the rear of the
unit is set to a different position, any change of function
will not take effect until the power supply has been
switched off and on again.
2. When switching over the replay from the memory card
to the USB storage medium (or vice versa), any function
selected (e. g. repeat function, single title replay, intro
function) will be deactivated. The position of the sliding
switch PLAY MODE defines if the replay will start auto-
matically after switching over or not.
6 Specifications
Frequency response: 20 – 19 000 Hz ± 2 dB
Output level: . . . . . . . 1.4 V
THD: . . . . . . . . . . . . . < 0.2 %
S / N ratio: . . . . . . . . . > 65 dB (A weighted)
Power supply: . . . . . 12 V
± 2 V, 120 mA
Ambient temperature: 0 – 40 °C
Dimensions: . . . . . . . 174 × 51 × 115 mm
Weight: . . . . . . . . . . . 494 g
Subject to technical modification.
If the module is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment.
Never put discharged batteries in the
household waste; always take them to
a special waste disposal, e. g. collec-
tion container at your re tailer.
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
A-1578.99.02.06.2015
®
DMP-30
Order number 17.4500
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
Button
on the audio player
on the remote control
Function
PLAY
MODE
sliding switch on the rear:
AUTO PLAY = The replay will start
automatically after the 12 V power
supply has been switched on.
NORMAL = The audio player will be
set to pause after the power supply
has been switched on.
RANDOM / AUTOPLAY = Replay in
random order will start automatically
after the power supply has been
switched on.
POWER
to switch on;
to switch off, keep button pressed for
3 s until
GoodBye
is indicated
FUNC
to switch between USB port
and memory card
PLAY
PAUSE
to start the replay and to switch
between replay and pause
1 … 9, 0
direct title selection, examples:
title 8 = buttons 8 and
title 30 = buttons 3, 0 and
title 125 = buttons 1, 2, 5 and
SKIP
previous / next title:
press button briefly
fast forward / reverse: keep button
pressed (sound muted in the process)
FOLDER
to go to the first title of the previous/
next folder
VOL+
VOL−
to increase/ decrease the volume:
press button briefly (repeatedly)
MUTE
to mute and unmute the sound
RANDOM
to activate and deactivate the replay
in random order
REPEAT
to select the repeat function:
REPEAT ALL
= all titles
REPEAT TRACK
= one title
REPEAT FOLDER
= all titles of
the folder
PLAY ALL
= function deactivated
INTRO
to activate and deactivate the intro
function (The first 10 seconds of
each title are replayed.)
PLAY 1
single title replay:
At the end of a title, the player is set
to pause. To start the next title, press
the button
/ PLAY PAUSE.
A-B
repeat of title section
(continuous loop)
Press the button at the beginning
and at the end of the section.
To exit the loop, press the button
once again.
ID 3
to switch the indication between title
information and storage device
selected (
USB
/
CARD
)
PROG
to program an individual title
sequence:
1. Press the button PROG
2. Enter the folder number and press
the button PROG
3. Enter the title number and press
the button PROG
4. Repeat these steps to program all
further titles (20 max.)
5. Press the button
to start the
replay
To delete or cancel the sequence,
press the button
/ STOP.
STOP
to stop the replay; the display will
indicate the storage device selected,
the number of folders and titles
English
