Immergas EOLO STAR 24 5E, Instruction Manual

13

C

32

C

32

C

32

C

32

1-17

1-19

1-18

1-16

1

2

3

6

4

7

5

1

2

3

6

8

4

7

5

MAKS 45%

MAKS 

MAKS 

MAKS 45%

INS

TALLER

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

The fixing plate kit includes:

N° 1 -  Gasket (1)

N° 1 -  Female concentric flange (2)

The Kit includes:

N° 1 -  Concentric intake-exhaust pipe Ø 

60/100 (3)

N° 1 -  Wall sealing plate (4)

N° 1 -  Aluminium tile (5)

N° 1 -  Fixed half-shell (6)

N° 1 -  Mobile half-shell (7)

The kit includes:

N° 1 -  Gasket (1)

N° 1 -  Female concentric flange 

(2)

 N°  1  -  Adapter   

Ø 80/125 (3)

N° 1 -  Concentric intake-exhaust 

pipe Ø 80/125 (4)

N° 1 -  Wall sealing plate (5)

N° 1 -  Aluminium tile (6)

N° 1 -  Fixed half-shell (7)

N° 1 -  Mobile half-shell (8)

1.13 CONCENTRIC VERTICAL KIT 

INSTALLATION.

Type C configuration, sealed chamber and 

fan assisted.

Concentric vertical intake and exhaust kit. This 

vertical terminal is connected directly to the 

outside of the building for air intake and flue 

gas exhaust.

NOTE:

 the vertical kit with aluminium tile 

enables installation on terraces and roofs with 

a maximum slope of 45% (approx. 25°) and the 

height between the terminal cap and half-shell 

(374 mm) must always be observed.

Vertical kit with aluminium tile Ø 60/100. 

To use this kit one must use the fixing plate kit 

60/100 (sold separately). 

Kit assembly (Fig. 1-16): install the concentric 

flange (2) on the central hole of the boiler inser-

ting the gasket (1) and tighten using the screws in 

the kit. Fit the male end (smooth) of the adapter 

(3) into the female end of the concentric flange 

(2). Imitation aluminium tile installation. Repla-

ce the tile with the aluminium sheet (5), shaping 

it to ensure that rainwater runs off. Position the 

fixed half-shell (7) and insert the intake-exhaust 

pipe (6). Fit the Ø 80/125 concentric terminal 

pipe with the male end (6) (smooth) to the female 

end of the adapter (3) (with lip gasket) up to the 

end stop; making sure that the wall sealing plate 

(4) has been fitted, this will ensure sealing and 

joining of the elements making up the kit.
•Extensions for vertical kit Ø 60/100 (Fig. 1-17). 

The kit with this configuration can be exten-

ded to 

a max. straight vertical length of 4.7 m

, 

including the terminal. This configuration 

corresponds to a resistance factor of 100. In 

this case specific extensions must be requested.

Vertical kit with aluminium tile Ø 80/125.

Kit assembly (Fig. 1-18): to install the kit Ø 

80/125 one must use the flanged adapter kit in 

order to install the flue system Ø 80/125. Install 

the flanged adaptor (2) on the central hole of the 

boiler, positioning gasket (1) with the circular 

projections downwards in contact with the boiler 

flange, and tighten using the screws contained 

in the kit. Installation of the fake aluminium 

tile: replace the tiles with the aluminium sheet 

(4), shaping it to ensure that rainwater runs off. 

Position the fixed half-shell (5) on the aluminium 

tile and insert the intake-exhaust pipe (7). Fit the 

Ø 80/125 concentric terminal pipe with the male 

side (smooth) to the female side of the adapter (1) 

(with lip gaskets) up to the end stop; making sure 

that the wall sealing plate (3) has been fitted, this 

will ensure sealing and joining of the elements 

making up the kit.
•  Extensions for vertical kit Ø 80/125 (Fig. 1-19). 

The kit with this configuration can be extended 

up to a 

max. length of 12.2 m

 including the ter-

minal. If additional components are assembled, 

the length equivalent to the maximum allowed 

must be subtracted. In this case specific exten-

sions must be requested.

MAXIMU

M LEN

GTH 4700 mm

MAXIMU

M LEN

GTH 12200 mm