background image

39

INS

T

ALLER

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

3.24  TECHNICAL DATA.

-  The flue temperature values refer to an air inlet 

temperature of 15°C and flow temperature of 
50°C.

-  The data relating to domestic hot water perfor-

mance refer to a dynamic inlet pressure of 2 bar 

and  an  inlet  temperature  of  15°C;  the  values 
are measured immediately at the boiler outlet, 
considering  that  to  obtain  the  data  declared, 
mixing with cold water is required.

-  (*) Efficiencies refer to the lower heating value.

-  (**) When the boiler is connected to an external 

storage tank unit.

Nominal heat input

kW (kcal/h)

34.9 (30040)

Minimum heat input

kW (kcal/h)

3.6 (3109)

Nominal heat output (useful)

kW (kcal/h)

34.2 (29412)

Minimum heat output (useful)

kW (kcal/h)

3.5 (3010)

(*) Effective thermal efficiency 80/60 Nom./Min.

%

97.9 / 96.8

(*) Effective thermal efficiency 50/30 Nom./Min.

%

103.4 / 107.5

(*) Effective thermal efficiency 40/30 Nom./Min.

%

106.0 / 107.6

Casing losses with burner On/Off (80-60°C)

%

0.35 / 0.10

Heat loss at flue with burner On/Off (80-60°C)

%

0.01 / 2.00

Central heating circuit max. operating pressure

bar

3.0

Maximum heating temperature

°C

90

Adjustable heating temperature (max operation field)

°C

20 - 85

System expansion vessel total volume

l

7.1

Expansion vessel factory-set pressure

bar

1.0

Appliance water content

l

2.4

Head available with 1000 l/h flow rate

kPa (m H

2

O)

37.2 (3.8)

(**) Hot water production useful heat output

kW (kcal/h)

34.2 (29412)

(**) Domestic hot water adjustable temperature

°C

30 - 60

Weight of full boiler

kg

35.8

Weight of empty boiler

kg

33.4

Electrical connection

V/Hz

230 / 50

Nominal power absorption

A

0.85

Installed electric power

W

120

Pump absorbed power

W

59

Fan power absorbed power

W

45

Value EEI

-

 0.20 - Part. 3

Equipment electrical system protection

-

IPX5D

Max temperature of combustion products

°C

75

NO

X

 class

-

5

Weighted NO

X

mg/kWh

26

Weighted CO

mg/kWh

24

Type of appliance

C13 / C13x / C33 / C33x / C43 / C43x / C53 / C63 

/ C83 / C93 / C93x / B23 / B33

Category

II 2H3P

Summary of Contents for VICTRIX MAIOR 28 - 35 TT 1 ERP

















































Reviews: