Immergas VICTRIX MAIOR 28 - 35 TT 1 ERP Instruction And Recommendation Booklet Download

Page: 5 / 48

1-1

INS

ALLER

MAINTEN

CE TECHNI

YES

BOILER

INSTALLATION

1.1 INSTALLATION

RECOMMENDATIONS.

The Victrix Maior 35 X TT 1 ErP boiler has been
designed for wall mounted installation only, to
heat and produce domestic hot water for domes-
tic use and similar purposes

(when the boiler is

connected to an external storage tank unit)

The  place  of  installation  of  the  appliance  and
relative Immergas accessories must have suitable
features (technical and structural) such to allow
(always  in  safety,  efficiency  and  comfortable
conditions):
-  installation (according to the provisions of the

technical legislation and technical regulations);

- maintenance operations (including scheduled,

periodic, routine and special maintenance);

- removal (to outdoors in the place for loading

and transporting the appliances and compo-
nents) as well as their eventual replacement
with appliances and/or equivalent components.

The wall surface must be smooth, without any
protrusions or recesses enabling access to the
rear part. They are not designed to be installed
on plinths or floors (Fig. 1-1).
By varying the type of installation the classifica-
tion of the boiler also varies, precisely:

Type B

or B

boiler if installed using the

relevant terminal for air intake directly from
the room in which the boiler has been installed.

Type C boiler

if installed using concentric

pipes or other types of pipes envisioned for
sealed chamber boilers for air intake and expul-
sion of flue gas.

Note:

appliance classification is provided in the

depictions of the various installation solutions
shown on the following pages.

Only professionally enabled companies are
authorised to install Immergas gas appliances.
Installation must be carried out according to
regulation standards, current legislation and in
compliance with local technical regulations and
the required technical procedures.
Before installing the appliance, ensure that it is
delivered in perfect condition; if in doubt, contact
the supplier immediately. Packing materials (sta-
ples, nails, plastic bags, polystyrene foam, etc.)
constitute a hazard and must be kept out of the
reach of children. If the appliance is installed in-
side or between cabinets, ensure sufficient space
for normal servicing; therefore it is advisable to
leave clearance of at least 3 cm between the boiler
casing and the vertical sides of the cabinet. Leave
adequate space above the boiler for possible water
and flue removal connections. Keep all flamma-
ble objects away from the appliance (paper, rags,
plastic, polystyrene, etc.).

Do not place household appliances underneath
the boiler as they could be damaged if the safety
valve intervenes, if the drain trap is blocked, or
if  there  are  leaks  from  the  hydraulic  connec-
tions;  otherwise,  the  manufacturer  cannot  be
held responsible for any damage caused to the
household appliances.
For the aforementioned reasons, we recommend
not  placing  furnishings,  furniture,  etc.  under
the boiler.
In the event of malfunctions, faults or incorrect
operation, turn the appliance off and contact an
authorised company (e.g. the Authorised Tech-
nical  Assistance  centre,  which  has  specifically
trained  staff  and  original  spare  parts).  Do  not
attempt to modify or repair the appliance alone.
Failure to comply with the above implies personal
responsibility and invalidates the warranty.

•

Installation regulations:

- this boiler can be installed outdoors in a

partially protected area. A partially protected
area is one in which the appliance is not
exposed to the direct action of the weather
(rain, snow, hail, etc..).

This type of installation is only possible when
permitted by the laws in force in the appliance's
country of destination.

- Installation in places with a fire risk is pro-

hibited (for example: garages, closed parking
stalls), gas appliances and relative flue ducts,
flue exhaust pipes and combustion air intake
pipes.

- Installation is prohibited on the vertical

projection of cooking hobs.

- Installation is also prohibited in places/en-

vironments that constitute common parts of
office condominiums such as stairs, cellars,
entrance  halls,  attics,  lofts,  escape  routes,
etc.  if  they  are  not  located  inside  technical
compartments  under  the  responsibility  of
each individual building and only accessible
to the user (for the features of the technical
compartments, see the technical standards in
force).

Attention:

wall mounting of the boiler must

guarantee stable and efficient support for the
generator

The plugs (standard supply) are only to be used
to fix the appliance to the wall;

they only ensure

adequate support if inserted correctly (according
to technical standards) in walls made of solid or
semi-hollow brick or block. In the case of walls
made from hollow brick or block, partitions with
limited static properties, or in any case walls
other than those indicated, a static test must be
carried out to ensure adequate support.

These  boilers  are  used  to  heat  water  to  below
boiling temperature in atmospheric pressure.
They  must  be  connected  to  a  central  heating
system  and  hot  water  circuit  suited  to  their
performance and capacity.

Attention:

The storage tank unit must also be

installed in an environment in which the tem-
perature cannot fall below 0°C.