background image

 

Support and Repairs 

The first line of support for ImmersionRC products should be the retailer that supplied the product. If 

for any reason that channel does not result in problem resolution, one of our repair centers may be 

able to help.  

 

ImmersionRC runs repair centers in the UK, and the USA. These centers are equipped with the 

knowledge to repair any of our products, whether or not the product is still covered under warranty.  

 

A simple email to 

repairs@immersionrc.com

 starts the support/repair process.  

 

Our Facebook-based community hub is also a great place to ask for help.  

facebook.com/groups/immersionrchub 
 

Troubleshooting 

 

Problem 

Cause 

Solution 

Rapidfire takes a long time to 

lock, and unlocks during 

short-range flights. 

Video quality doesn’t seem 

right.  

Seen on a few Chinese flight 

controllers with OSDs 

(MAX7456) which use 

under-sized output capacitors, 

and result in distorted video 

syncs.  

 

Sunrise 30A 4-in-1 is known to 

have this problem (sold under 

several brand names) 

Bypass the OSD, and hook the 

camera directly to the vTx in 

order to prove that this is the 

problem.  

Replace ‘Cout + Csag’ with 

47uF ceramic capacitors as a 

permanent fix.  

Contact your FC manufacturer 

and let them know that you are 

not happy!  

 

 

 

 

 

 

 

 

Summary of Contents for rapidFIRE



















Reviews: