Immersion RC Vortex 230 Mojo, Quick Start Manual

1)​ ​Install​ ​Compatible​ ​R/C​ ​Receiver 

The​ ​Vortex​ ​230​ ​Mojo​ ​is​ ​shipped​ ​with​ ​three​ ​receiver​ ​interface​ ​cables,​ ​supporting​ ​4​ ​commonly​ ​used 
interfaces.  

a) 3-Pin​ ​0.1”​ ​Servo​ ​Cable,​ ​for​ ​S-Bus,​ ​and​ ​CPPM​ ​(5V) 
b) 5-pin​ ​Picoblade​ ​for​ ​FrSky​ ​XSR​ ​receivers​ ​(5V) 
c) 3-pin​ ​JST-ZH​ ​for​ ​Spektrum​ ​DSMX​ ​receivers​ ​(3V) 

Receivers​ ​may​ ​be​ ​mounted​ ​externally​ ​on​ ​the​ ​tail-end​ ​of​ ​the​ ​quad,​ ​or​ ​internally.​ ​Internally​ ​is​ ​definitely​ ​the 
preferred​ ​solution​ ​but​ ​does​ ​require​ ​a​ ​suitably​ ​small​ ​receiver​ ​and​ ​means​ ​having​ ​to​ ​remove​ ​the​ ​top​ ​plate​ ​to 
install​ ​the​ ​receiver. 

The​ ​following​ ​are​ ​recommended​ ​for​ ​internal​ ​installation:  

1) FrSky​ ​​XSR​,​ ​using​ ​the​ ​supplied​ ​XSR​ ​cable 
2) FrSky​ ​​X4R-SB​,​ ​‘Naked’​ ​version​ ​with​ ​SBus​ ​output 

Requires​ ​some​ ​soldering​ ​to​ ​wire​ ​sbus​ ​cable 

3) Spektrum​ ​​SPM4648​ ​​Auto-bind​ ​receiver​ ​with​ ​supplied​ ​DSMX​ ​cable 

Remove​ ​plastic​ ​case​ ​and​ ​heat-shrink​ ​for​ ​optimal​ ​fit 

4) Spektrum​ ​​SPM9646​ ​​Carbon​ ​fuse​ ​receiver 
5) Spektrum​ ​​SPM9649T​ ​​Telemetry​ ​receiver 

To​ ​access​ ​the​ ​receiver​ ​bay​ ​for​ ​internal​ ​receiver​ ​mounting,​ ​remove​ ​the​ ​8​ ​screws​ ​which​ ​secure​ ​the​ ​top​ ​plate 
to​ ​the​ ​arms,​ ​and​ ​carefully​ ​remove​ ​the​ ​top​ ​assembly,​ ​which​ ​includes​ ​the​ ​camera​ ​unit.  

The​ ​(4-pin)​ ​receiver​ ​connector​ ​is​ ​pictured​ ​below.​ ​To​ ​mount​ ​the​ ​receiver,​ ​a​ ​small​ ​piece​ ​of​ ​double-sided​ ​tape 
may​ ​be​ ​used​ ​on​ ​the​ ​top​ ​of​ ​the​ ​metal​ ​can​ ​in​ ​the​ ​receiver​ ​bay.  

4