9. Specifications
9.1 Standard specifications
Mounting method
: Flush
Setting
method
: Input system using membrane sheet key
Display
PV display : Red LED 4 digits, character size 10.2 x 4.9 mm (H x W)
SV display
: Green LED 4 digits, character size 8.8 x 4.9 mm (H x W)
Accuracy (Setting and Indication)
:
Thermocouple
:
Within
0.2% of each input span 1digit, or within 2
(4 ),
whichever is greater
However R, S inputs, 0 to 200
(400 ): Within 6 (12 )
B input, 0 to 300
(600 ): Accuracy is not guaranteed
K, J, E, T, N inputs, less than 0
(32 ): Within 0.4% of input span 1digit
RTD
:
Within
0.1% of each input span 1digit, or
within 1
(2 ), whichever is greater
DC
current
:
Within
0.2% of each input span 1digit
DC
voltage
:
Within
0.2% of each input span 1digit
Input sampling period
: 0.25 seconds
Input
Thermocouple :
K, J, R, S, B, E, T, N, PL- , C(W/Re5-26)
External resistance, 100 or less
(However, B input: External resistance, 40 or less)
RTD : Pt100, JPt100, 3-wire system
Allowable input lead wire resistance (10
or less per wire)
DC current
: 0 to 20mA DC, 4 to 20mA DC
Input impedance: External shunt resistor 50
Allowable input current (50mA or less)
DC voltage
: 0 to 1V DC Input impedance (1M
or greater)
Allowable input voltage (5V or less)
Allowable signal source resistance (2k or less)
: 0 to 5V DC, 1 to 5V DC, 0 to 10V DC Input impedance (100k
or greater)
Allowable input voltage (15V or less)
Allowable signal source resistance (100 or less)
OUT1 output
Relay contact : 1a, Control capacity 3A 250V AC (resistive load)
1A 250V AC (inductive load cosø=0.4)
Electrical life, 100,000 times
Non-contact voltage (For SSR drive): 12
+2
V DC maximum 40mA (short circuit protected)
0
DC current : 4 to 20mA DC, Load resistance, maximum 550
A1 output
Action : ON/OFF action
Hysteresis
: 0.1 to 100.0
( ), or 1 to 1000
Output : Relay contact 1a
Control capacity, 3A 250V AC (resistive load)
Electrical life, 100,000 times
Control action
PID action (with auto-tuning function)
PI action: When derivative time is set to 0
PD action (with auto reset function): When integral time is set to 0
P action (with auto reset function): When derivative and integral times are set to 0.
ON/OFF action: When proportional band is set to 0 or 0.0
OUT1 proportional band : 0 to 1000
(2000 ), 0.0 to 999.9 ( ) or 0.0 to 100.0%
(ON/OFF action when set to 0 or 0.0)
Integral time
: 0 to 1000s (OFF when set to 0)
Derivative time
: 0 to 300s (OFF when set to 0)
OUT1 proportional cycle : 1 to 120s (Not available for DC current output type)
ARW
: 0 to 100%
OUT1 ON/OFF action hysteresis: 0.1 to 100.0
( ), or 1 to 1000
OUT1 high limit setting : 0 to 100% (DC current output type: –5 to 105%)
16
Power
Isolated
Power
supply
A1
CPU
CT
input
OUT1
Input
EVT (A2, LA, W) or OUT2 (DT)
15
5
4
3
9
8
1
2
12
7
6
11
10
13
14
SV2
Commu-
nication
14
13
OUT1 low limit setting : 0 to 100% (DC current output type: –5 to 105%)
Circuit isolation configuration
