background image

TROUBLESHOOTING

12

PROBLEM

POSSIBLE CAUSE

REMEDY

The compressor stopped
and does not start.

The compressor does not
reach the set pressure
and overheats easily.

Compressor does not
start.

Bad connections.

Overload cutout switch has
tripped or duty cycle has been
exceeded.

Motor windings burnt out.

Compressor head gasket blown
or valve broken.

Air receiver charged

Check electrical connections. Clean
and tighten as necessary.

Switch off and wait approx 5 minutes
before pressing the reset button and
switching on again.

Contact your local Impax dealer for a
replacement motor.

Wait for compressor to cool down,
disassemble head and replace any
broken components. Carefully clean
all sealing surfaces before
reassembling. If in doubt contact your
Impax dealer.

Open drain valve to expel air.
Compressor should start again when
pressure reduces to approx. 115 psi.

ENVIRONMENTAL PROTECTION

Information for (private householders) for the environmentally responsible disposal of Waste
Electrical and Electronic Equipment (WEEE)

This symbol on products and or accompanying documents indicates that used
and end of life electrical and electronic equipment should not be disposed of in
household waste. For the proper disposal, treatment, recovery and recycling,
please take these products to designated collection points, where they will be
accepted on a free of charge basis. Alternatively, in some countries you may be
able to return your products to your retailer upon the purchase of an equivalent
new product. Disposing of this product correctly will help to save valuable
resources and prevent any potential adverse effects on human health and the

environment which could otherwise arise from inappropriate waste disposal and handling. Please
contact your local authority for further details of your nearest designated collection point. Penalties
may be applicable for incorrect disposal of this waste in accordance with national legislation.

FOR BUSINESS USERS IN THE EUROPEAN UNION.

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.

Information on Disposal in other Countries outside the European Union.

This Symbol is only valid in the European Union.
If you wish to dispose of this product, please contact your local authorities or dealer and ask for the
correct method of disposal.

Summary of Contents for IM180-6L

















Reviews: