background image

5

IMPERIAL TRUCK MOUNTED VACUUM TANKER MANUAL

SAFETY PRECAUTIONS

General Safety Precautions 

Follow these safety precautions, and insist that those 
working with you follow them.

Most industrial equipment accidents can be avoided 
by observing safety precautions. Remember: a careful 
operator is the best insurance against an accident.

Safety Precautions for Handling Effl uent

  DANGER

:  DO  NOT  stand  near  the  oil  catch 

muffl er or discharge valve when loading or unloading 
the  tank.  Sewer  gases  vented  out  of  the  oil  catch 
muffl er will settle downward. Sewer gases can also be 
expelled out of the discharge valve when releasing 
tank pressure. Inhaling sewer gases can cause severe 
injury or death.

 WARNING

: DO NOT allow children or irresponsible 

people near your work area or equipment. Fatalities 
have occurred when children have fallen or climbed 
into unattended septic/holding tanks. Secure your 
work  area  from  entry  of  unauthorized  persons  in 
the vicinity. 

 WARNING

:  Secure  all  access  covers  against 

unauthorized entry after pumping a septic/holding 
tank. Fatalities have occurred where children have 
fallen into septic/holding tank openings that had not 
been properly secured. Securely chain and padlock 
above ground access openings. Bury underground 
access openings by at least six inches of dirt.

 

WARNING

: Always wear protective gloves, eye 

protection and, appropriate clothing when working 
with  sewage  effl uent  or  septage. These  materials 
may  contain  hazardous  chemicals,  disposed  of 
through  the  drain,  which  can  cause  severe  injury 
or even death due to contact. These effl uents also 
contain bacteria, which can be a source of infection, 
especially if exposed to open cuts or sores. 

Safety Precautions for Entering Tanks

 

 DANGER:

 DO NOT enter a transport, septic, or 

holding tank without fi rst cleaning and providing 
adequate  ventilation  to  the  interior  of  the  tank. 
Sewer gas is deadly if inhaled; in addition, it depletes 
the  oxygen  in  a  confi ned  space,  which  can  cause 
asphyxiation.

 

 DANGER:

 DO NOT enter a transport, septic, or 

holding tank without using a respirator that supplies 
grade D breathing air or a self-contained breathing 
apparatus. In addition, DO NOT use this equipment 
without training and familiarity with it. Entering a 
tank exposed to sewage effl uent without a correct 
breathing apparatus, or with improper use of it, can 
cause death.
 
 

 

DANGER:

 DO NOT enter a transport, septic, or 

holding tank without protective clothing. Sewer gas 
can be absorbed through the skin causing serious 
injury or death.

 

 

WARNING:

 When entering a transport, septic, or 

holding tank, always have someone standing by to 
provide assistance, and always have a respirator that 
supplies grade D breathing air or a self-contained 
breathing apparatus on hand for them. In the event 
of an attempted rescue, this equipment is necessary 
to prevent death of the rescuer.

 

 WARNING

: Attach a safety-harness and rope to 

any person that enters a transport, septic, or holding 
tank. Have the safety-harness rope held by a person 
standing by to provide assistance outside the tank. 
An  attempted  rescue  without  the  advantage  of 
a rope and harness can be life threatening to the 
rescuer.

 

 WARNING

:  Entry  into  a  transport,  septic,  or 

holding  tank  is  confined  space  entry.  Persons 
entering  these  tanks  for  any  purpose  must  be 
trained in and follow OSHA confi ned space safety 
procedures.

�����������������������������������������������������������

����������������������������������������������������

������������������������������������������������������

������������������������������������������������������

DANGER

������������������������

����������������������

����������������������

��������������������������������������������������

����������������������������������������������������

���������������������������������������������������

����������������������������������������������������

��������������������������������������������������������

������������������������������������������������������

DANGER

��������������������

�����������������������

����������������

Summary of Contents for TMV-1500































Reviews: