background image

 

 

 
 

TABLE OF CONTENTS 

 

BEFORE YOU BEGIN...................................................................................... 

IMPORTANT SAFETY NOTICES..................................................................... 

HARDWARE IDENTIFIER.....…....................................................................... 

ASSEMBLY INSTRUCTIONS........................................................................... 

EXPLODED DIAGRAM………………………………………………………………  

PARTS LIST...................................................................................................... 

10 

WARRANTY.................................................................................................…. 11 
ORDERING PARTS.......................................................................................… 

11

 

 

 

 
 

 
 
 
BEFORE  YOU  BEGIN 

 

Thank you for selecting the APEX POWER TOWER TC-2210 by IMPEX 
INC.  For your safety and benefit, read this manual carefully before using 
the machine.   As a manufacturer, we are committed to provide you 
complete customer satisfaction.  If you have any questions, or find there 
are missing or damaged parts, we guarantee you complete satisfaction 
through direct assistance from our factory.  To avoid unnecessary delays, 

please call our  TOLL-FREE customer service number.  

Our Customer 

Service Agents will provide immediate assistance to you. 

 

 

 

Toll-Free Customer Service Number       

1-800-999-8899 

Mon. - Fri. 9 a.m. - 5 p.m.  PST 

www.impex-fitness.com 

info@impex-fitness.com

 

Summary of Contents for Apex TC-2210













Reviews: