background image

 

 

 
 

TABLE OF CONTENTS 

 

BEFORE YOU BEGIN...................................................................................... 

IMPORTANT SAFETY NOTICES..................................................................... 

HARDWARE IDENTIFIER.....…....................................................................... 

ASSEMBLY INSTRUCTIONS........................................................................... 

EXPLODED DIAGRAM………………………………………………………………  

PARTS LIST...................................................................................................... 

10 

WARRANTY.................................................................................................…. 11 
ORDERING PARTS.......................................................................................… 

11

 

 

 

 
 

 
 
 
BEFORE  YOU  BEGIN 

 

Thank you for selecting the Iron Grip Strength POWER TOWER IGS-2110 
by IMPEX INC.  For your safety and benefit, read this manual carefully 
before using the machine.   As a manufacturer, we are committed to 
provide you complete customer satisfaction.  If you have any questions, or 
find there are missing or damaged parts, we guarantee you complete 
satisfaction through direct assistance from our factory.  To avoid 
unnecessary delays, 

please call our  TOLL-FREE customer service 

number.  

Our Customer Service Agents will provide immediate assistance 

to you. 

 

 

 

Toll-Free Customer Service Number       

1-800-999-8899 

Mon. - Fri. 9 a.m. - 5 p.m.  PST 

www.impex-fitness.com 

info@impex-fitness.com

 

Summary of Contents for Iron Grip Strength IGS-2110













Reviews: