background image

 

STEP 4   (See Diagram 4) 

A.) Slide the Sliding Weight Post (#22) onto the Weight Glide Post (#16). 

The triangular 

bracket on Sliding Weight Post needs to be behind the Weight Glide Post and facing 
upward. 

 

B.) Attach the Weight Glide Post to the Lat Bar Frame (#17). Attach one 3 1/8” x 1 ¾” Bracket 

(#29) to the Weight Glide Post. Secure the upper hole with one M10 x 2 ½” Allen Bolt (#88) 
and one Ø ¾” Washer (#81). Secure the lower hole with one M10 x 2 ½” Carriage Bolt 
(#67), one Ø ¾” Washer (#81), and one M10 Aircraft Nut (#83). 

C.) Attach the Weight Glide Post to the Lower Pulley Frame (#15). Attach one 3 1/8” x 1 ¾” 

Bracket (#29) to the Weight Glide Post. Secure the upper hole with one M10 x 2 ½” 
Carriage Bolt (#67), one Ø ¾” Washer (#81), and one M10 Aircraft Nut (#83). Secure the 
lower hole with one M10 x 2 ½” Allen Bolt (#88) and one Ø ¾” Washer (#81). 

D.) 

Securely tighten all Nuts and Bolts installed in Step-1, Step-2, Step-3, and Step-4.

 

E.) Attach the Butterfly Base (#10) to front Middle Vertical Frame. Attach the Butterfly Pulley 

Bracket (#13) to the Middle Vertical Frame from rear. Secure them together with two M10 x 
2 ½” Carriage Bolts (#67), two Ø ¾” Washers (#81), and two M10 Aircraft Nuts (#83). 

F.) Attach the Butterfly Stopper (#60) to Butterfly Base. Secure it with two M6 x 3/8” Allen Bolts 

(#78). 

G.) Attach two Swivel Pulley Brackets (#14) to the Butterfly Pulley Bracket. Secure each with 

one M12 x 4 7/8” Hex Bolt (#79), one Ø 1” Washer (#82), and one M12 Aircraft Nut (#84). 

H.) Insert the pivot one Left Butterfly (#11) to the Butterfly Base from bottom. Secure it with one 

M10 x 5/8” Allen Bolt (#71) one Ø ¾” Washer (#81), and one Lock Ring (#28). Push a 
Butterfly Foam Roll (#40) to Left Butterfly. 

I.) Repeat H to install the Right Butterfly (#12). 
J.) Attach the Backrest Board (#34) to Middle Vertical Frame. Secure it with two M8 x 2 3/8” 

Allen Bolts (#77) and two Ø 5/8” Washers (#80). 

K.) Attach two Olympic Sleeves (#49) to the Sliding Weight Post. Attach a Spring Clip (#50) to 

each Olympic Sleeve. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

12 

Summary of Contents for MARCY DIAMOND MD-8870



































Reviews: