background image

PRECAUTIONS 
 

This exercise machine is built for optimum safety.  However, certain precautions apply 
whenever you operate a piece of exercise equipment.  Be sure to read the entire manual 
before you assemble or operate your machine.  In particular, note the following safety 
precautions: 
 

1. 

 Keep children and pets away from the machine at all times.  DO NOT leave  

children unattended in the same room with the machine. 

 2.  Only one person at a time should use the machine. 
 3.  If the user experiences dizziness, nausea, chest pain, or any other abnormal 

symptoms, STOP the workout at once.  CONSULT A PHYSICIAN IMMEDIATELY. 

 4.  Position the machine on a clear, leveled surface.  DO NOT use the machine near water 

or outdoors. 

 5.  Keep hands and feet away from all moving parts. 
 6.  Always wear appropriate workout clothing when exercising.  DO NOT wear robes or 

other clothing that could become caught in the machine.  Running or aerobic shoes are 
also required when using the machine. 

 7.  Use the machine only for its intended use as described in this manual.  DO NOT use 

attachments not recommended by the manufacturer. 

 8.  Do not place any sharp object around the machine. 
 9.  Disabled person should not use the machine without a qualified person or physician in 

attendance. 

10. Before using the machine to exercise, always do stretching exercises to properly warm 

up. 

11. Never operate the machine if the machine is not functioning properly. 
12. A spotter is needed during exercise. 

Do not use this product alone.

 

13. This machine is designed and intended for home and consumer use only, not for 

commercial use. 

   14. 

Make sure the Foot Lock securely locks both feet.

 

15. 

When doing inversion exercises, please hold onto the Handles with both hands. 

 
CARE AND MAINTENANCE 

1. Lubricate moving parts with WD-40 or light oil periodically. 
2. Inspect and tighten all parts before using the machine. 
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.  
    DO NOT use solvents. 
4. Maximum user’s weight: 300 lbs. 
 

WARNING:  BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR 
PHYSICIAN.  THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE 
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS.  READ ALL 
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.  IMPEX INC. ASSUMES 
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE 
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. 
SAVE THESE INSTRUCTIONS. 

 
 

WARNING LABEL PLACEMENT 

 

Summary of Contents for MARCY IVT-600















Reviews: