Impex MARCY IVT-600 Owner'S Manual Download | Manualshive

Page: 6 / 14

background image

ASSEMBLY INSTRUCTION

Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine
to avoid possible injury.
Tools required to assembly the machine: Adjustable Wrench and Allen Wrenches.

STEP 1 (See Diagram 1)

A.)

Do not fasten the Nuts and Bolts until instructed to do so.

B.) Place the Rear Base Frame (#7) on a flat surface.
C.) Insert the Left & Right Rear Support Frames (#2 &#6) into the Rear Base Frame.
D.) Secure each Rear Support with two M6 x 5/8” Allen Bolts (#38) and two Ø ½”

Washers (#40).

DIAGRAM 1

5

«
...
4
5
6
7
8
...
»

Summary of Contents for MARCY IVT-600















Reviews:

No comments

Related manuals for MARCY IVT-600

Brand: GE Pages: 242

Brand: GE Pages: 24

Brand: Balanced Body Pages: 3

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: Xebex Fitness Pages: 15

Brand: qeedo Pages: 2

Aspect Q-CARD 100-4T

Brand: idi Pages: 38

Brand: K-LASER Pages: 70

Brand: K-LASER Pages: 72

Brand: Taylor Pages: 41

Brand: Olympus Pages: 56

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

Brand: Yamaha Pages: 29

Brand: Yamaha Pages: 45

Brand: Mindray Pages: 295

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands