background image

©

 IMPEX INC.                                                                                                                               www.impex-fitness.com 

10 

CARE AND MAINTANCE 

 
 

1.  Inspect and tighten all parts each time you use the bike.  Replace any worn parts 

immediately.   

2.  The bike can be cleaned using a damp cloth and mild non-abrasive detergent.  Do not use 

solvents. 

3.  Store the bike IN-DOOR.  Excess moisture and water would cause rust on the frame. 
4.  The Bike shall be placed at least 24 inches away from the wall or/and any other object such 

as furniture to provide safe access to and passage around the bike. 

5.  To avoid possible injury, the help of two or more people are needed when moving the bike 

around. 

6.  Disposal Instructions – The equipment can be safely disassembled and disposed without 

unreasonable hazards.  Call your local recycle agency regarding details of recycling. 

7. 

The maximum user weight is 300 lbs.

 

8. 

Assembled Dimension: 45.5” x 20” x 44”

 

 

 

OPERATING NOTES 

 

 

ADJUSTMENT 

1.  Use the Tension/Brake Knob (#21) to adjust the resistance for exercises. 
2.  Loosen and pull out the Lock Knob (#19).  Slide the Seat Post to the desired height and 

lock at the position by fastening the Lock Knob (#19). 

3.  Loosen and pull out Lock Knob (#19 & #43). Slide Handle Post to desired height and 

Lock at the position by fastening the Lock Knob (#19 & #43). 

4.  The seat height adjustment is in approximately 1” increment.  

*The seat height can be adjusted for 10 different height ranges from 35” to 44”. 

5.  The height of Elbow Support can be adjusted with 6 positions range from 36” to 41” with 

approximately 1” adjustment. 

6.  Loosen and pull out the Seat Lock Knob (#29). Slide the Seat Support to the desired 

position and lock at the position by fastening the Seat Lock Knob. 

7.  Loosen the L-shaped Lock Knob (#13), move the Handle Sliding Block (#10) to desired 

position; lock the Handle at position by fastening the L-shaped Lock Knob.  

 

1.  Press down the Tension/Brake Knob (#21) to stop the fly wheel.  ONLY when 

the flywheel has stopped, will it be safe to remove feet from pedals. 

Stopping the Exercise 

2.  DO NOT stop pedaling: doing so could result in serious injury. 
3.  DO NOT attempt to stop the Fly Wheel by hands, feet or any other device not 

indicated in this instruction. 

 

 

TRANSPORT 

The Bike has a pair Roller Wheels on Front Stabilizer.  
To move, carefully tilt the cycle forward, and then roll. 

 
 
 
 
 
 
 
 

Summary of Contents for MARCY JX-7038















Reviews: