background image

IMPEX INC. 

 

LIMITED WARRANTY 

 

IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under 
normal use and service conditions, for a period of  two years on the Frame from the date of purchase.   This 
warranty extends only to the original purchaser.   IMPEX's obligation under this Warranty is limited to 
replacing or repairing, at IMPEX's option. 
 
All returns must be pre-authorized by IMPEX.  Pre-authorization may be obtained by calling IMPEX 
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be 
prepaid by the customer.  This warranty does not extend to any product or damage to a product caused by 
or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an 
IMPEX authorized service center or for products used for commercial or rental purposes.  No other warranty 
beyond that specifically set forth above is authorized by IMPEX. 
 
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in 
connection with the use or performance of the product or other damages with respect to any economic loss, 
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other 
consequential damages or whatsoever natures.   Some states do not allow the exclusion or limitation of 
incidental or consequential damages.  Accordingly, the above limitation may not apply to you. 
 
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of 
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth 
herein.  Some states do not allow limitations on how long an implied warranty lasts.   Accordingly, the above 
limitation may not apply to you. 
 
This warranty gives you specific legal right.   You may also have other rights which vary from state to state. 

Register on-line at www.impex-fitness.com

 

 

IMPEX INC. 

14777 Don Julian 

City of Industry, CA  91746 

 
ORDERING REPLACEMENT PARTS 

 
Replacement parts can be ordered by calling our Customer Service Department toll-free at 

1-800-999-8899

 

during our regular business hours:  Monday through Friday, 9 am until 5 pm Pacific standard time. 

info@impex-fitness.com 

 
When ordering replacement parts, always give the following information. 
 
1. Model 
2. Description of Parts 
3. Part  Number 
4. Date of Purchase 
 
 
 

 
 
 
 

22 

Summary of Contents for POWERHOUSE SM 3000
























Reviews: