background image

 
 
 
 

TABLE OF CONTENTS 

 

BEFORE YOU BEGIN....................................................................................................... 

IMPORTANT SAFETY NOTICE........................................................................................ 

HARDWARE IDENTIFIER................................................................................................ 

ASSEMBLY INSTRUCTIONS........................................................................................... 

EXPLODED DIAGRAM..................................................................................................... 

11 

PARTS LIST...................................................................................................................... 12 
WARRANTY...................................................................................................................... 

13 

ORDERING PARTS.......................................................................................................... 

13

 

 
 
 

 
 
 
 
 

BEFORE  YOU  BEGIN 

 

Thank you for selecting the WM-MXS BENCH by IMPEX FITNESS 
PRODUCTS.  For your safety and benefit, read this manual carefully 
before using the machine.   As a manufacturer, we are committed to 
provide you complete customer satisfaction.  If you have any 
questions, or find there are missing or damaged parts, we guarantee 
you complete satisfaction through direct assistance from our factory.  
To avoid unnecessary delays, please call our  TOLL-FREE customer 
service number.  
Our Customer Service Agents will provide 
immediate assistance to you. 

 

 

 

Toll-Free Customer Service Number       

1-800-999-8899 

Mon. - Fri.  9 a.m. - 5 p.m.  PST 

www.impex-fitness.com 

info@impex-fitness.com 

 

Summary of Contents for WM-MXS















Reviews: