background image

11

SPECIFICATIONS

Model

BMS
(Baseboard Module System)

System

GA 610

General Data

Frequency

70 cm Band (Selectable 
458.800 Mhz to 459.175 
Mhz) or CS434

Range

approx. 100 m ( 328 ft.)

Address

20-bit - 1,000,000 possible

Operating temperature

-30° to +70° C 
(-22° F to 158° F)

Data Format

2400/4800 Baud, even 
parity, 8 data bits, 2 stop bits, 
hamming distance 4

Receiver

Protective System

IP 65

System

Synthesizer Technology

Voltage Supply

12 to 24 VDC (-50% - +20%)

Decoding

Multiple bit scanning, 
self-monitoring

Fuses

7.5 amp. / 80 V car fuse

Output

Intrinsically safe emergency 
stop with two MOS - FET - 
transistors, 12 digital 
outputs, potential free 250 V 
/ 8 A, 6 analog outputs, 2 
speed ranges

Static current

260 mA, Stand-by 

Antenna connection

TNC - socket

Dimensions (approx. with 
rubber buffer) 
L x B x H

265 mm x 161 mm x 111 mm

Weight - Kg (lbs)

2,5  (   )

Transmitter

Protection type

9.0 (23)

Battery Pack

3.6 V / 1200 mAh (NiMh)

Operating time

approx 20 h

Transmitting power

< 10 mW

Current rating, Self test

approx. 75 mA

Current rating, 
Transmission

approx. 83 mA

GL - Dimensions (with 
protection frame)

300 mm x 180 mm x 180 mm

GL - Weight (including 
battery and belt)

2.4 Kg

Nova - Dimensions (with 
protection frame)

230 mm x 170 mm x 106 mm

Nova - Weight (including 
battery and belt)

1.8 Kg

Battery Charger

Operating voltage

12/24 VDC

Charging current

300 mA

Open-circuit voltage

15 - 22V

Summary of Contents for 16000-SIII















Reviews: