1 - 2
99906549 rev 00 (JANUARY-2020)
SECTION 1: SAFETY
IOWA MOLD TOOLING CO., INC.
(641) 923-3711
CAS40PL, CAS40PL-CW, CAS40PLE, CAS40PLE-CW
NOTE
Slowly remove
fi
ll cap to vent compressor
sump pressure.
•
DO NOT
use the compressor for purposes oth-
er than for which it is intended. High pressure
air can cause serious and even fatal injuries.
•
DO NOT
operate the compressor outside of its
speci
fi
ed pressure and speed ratings. (See
Section 2: Speci
fi
cations or refer to the equip-
ment data plate.).
•
DO NOT
use
fl
ammable solvents or cleaners
for cleaning the compressor or its parts.
•
DO NOT
operate the compressor in areas
where
fl
ammable, toxic, corrosive fumes, or
other damaging substance can be ingested by
the compressor intake.
• Keep arms, hands, hair and all other body parts,
and clothing away from fans, drive shafts, and
other moving parts.
•
DO NOT
wear jewelry, unbuttoned cu
ff
s, ties,
or loose-
fi
tting clothing when you are working
near moving/rotating parts.
•
ALWAYS
con
fi
ne long hair when working near
moving/rotating parts.
•
NEVER
operate the equipment while wearing a
headset to listen to music or the radio.
• Wear personal protective equipment such as
gloves, work shoes, and eye and hearing pro-
tection as required for the task at hand.
•
DO NOT
operate the compressor with any
guards removed or damaged, or other safety
devices inoperative.
•
DO NOT
operate the compressor in enclosed
or con
fi
ned spaces where ventilation is re-
stricted or closed-o
ff
.
• Ensure that hoses connected to service valves
are
fi
tted with correctly sized and rated
fl
ow
limiting devices which comply with applicable
codes. Pressurized broken or disconnected
hoses can whip, causing injuries or damage.
•
DO NOT
use tools, hoses, or equipment that
have maximum ratings below that of this com-
pressor.
• Keep metal tools, and other conductive objects
away from live electrical components.
• Before performing maintenance or repair oper-
ations on the compressor, ensure that all pow-
er has been removed and been locked out to
prevent accidental application.
•
DO NOT
assume that because the compressor
is in a STOPPED condition that hydraulic pow-
er has been removed.
• Use this compressor only to compress atmo-
spheric air. Use of this equipment as a booster
pump and/or to compress any other gaseous
or aerosol substance constitutes improper
use. It can also cause damage or injuries.
Such misuse will also void the warranty.
• Install, operate, and maintain this equipment in
full compliance with all applicable OSHA, oth-
er Federal, state, local codes, standards, and
regulations.
• When lifting objects, be aware of proper lifting
techniques to avoid injury.
•
ALWAYS
read and follow safety related pre-
cautions found on containers of hazardous
substances.
1.3.3
CAUTIONS
CAUTION
Identi
fi
es actions or conditions which will or
can cause injuries, equipment damage or mal-
functions.
• Check all safety devices for proper operation
on a routine basis.
• Ensure that no tools, rags, or other objects are
left on compressor drive systems or near in-
takes.
• Keep the equipment clean when performing
maintenance or service actions. Cover open-
ings to prevent contamination.
•
DO NOT
operate the compressor if cooling air
is not available (fan/cooler not operating) or if
lubricant levels are below their speci
fi
ed min-
imum levels.
• Ensure all plugs, hoses, connectors, covers,
and other parts removed for maintenance ac-
Summary of Contents for CAS40PL
Page 2: ...BLANK PAGE...
Page 81: ...BLANK PAGE...
