45
Standard Accessories
Your HERMIT comes equipped with one each of the following stan-
dard accessories:
• HERMIT 2000 Operator’s Manual
• HERMIT 2000 Pocket Guide
• Factory-installed lithium battery pack
• Serial interface cable kit for connection to the RS232C port, in-
cluding:
– Serial cable with 6-pin circular to DB9 female connector
– DB9 male to DB25 male adapter
– DB9 male to DB25 female adapter
• External power pack, including:
– 12 VDC automobile cigarette lighter adapter
– 120 VAC to 15 VDC wall-mount power pack
• Alarm interface cable
• DataTransfer software for transferring raw data from the HER-
MIT to the IBM PC and compatibles.
Optional Accessories
In addition to the standard accessories shipped with your HERMIT,
In-Situ also makes available the following optional accessories.
Input Channel Expansion
The HERMIT 2000 is available in standard configuratinos of 4, 8,
12, and 16 input channels. Configurations with up to 32 input chan-
nels are available on special order. Input channel expansion requires
installation by the factory.
Memory Expansion
Non-volatile data storage memory for the HERMIT 2000 is available
in the following configurations:
• 64K bytes--standard with 4- and 8-channel instruments
• 128K bytes--standard with 12- and 16-channel instruments
• 192K, 256K, 320K, 384K. 448K, and 512K bytes
Field Printers
•
SE1004B 24-Column Printer.
The SE1004B is a compact, light-
weight printer that permits low to moderate speed printouts of
tabularized and graphic data. The SE1004B requires an external
12 VDC power source for operation and includes adapters for an
automobile cigarette lighter and 120 VAC wall outlet.
•
GFP-80 80-Column Printer.
The GFP-80 is a high speed, por-
table field printer that permits printouts of multi-column,
tabularized data and large 8.5 K 11 inch, high-resolution graphic
data. It operates on its own internal, rechargeable battery pack.
Transducers
All of In-Situ’s transducers come to the customer ready to use: fully
calibrated and complete with cable, reel, and pre-wired connectors.
• Pressure. Pressure transducers can be used with the HERMIT to
measure pressure, level, and flow. In-Situ offers a variety of pres-
sure transducer sizes and ranges to cover most measurement re-
quirements.
•
Conductivity/Temperature.
A dual-mode transducer, the conduc-
tivity/temperature probe permits the simultaneous measurement of
both conductivity and temperature while using only one input chan-
nel. The HERMIT can be programmed to provide readings of un-
compensated or temperature-compensated conductivity.
•
pH/Temperature.
Also a dual-mode transducer, the pH/tempera-
ture probe permits measurement of temperature and tempera-
ture-compensated pH on one channel.
•
Barometric Pressure.
This transducer provides an accurate mea-
surement of absolute pressure in the 8 to 16 PSIA range. Pressure is
displayed in PSIA; conversion factors are provided to display results
in mm Hg, inches H2O, and inches Hg, to name a few.
Shipping Containers
Heavy-duty polyethylene shipping containers are water-tight, pres-
sure- tight to 0.5 psi, have sturdy and comfortable carrying handles,
and can be used as a seat in the field. They are approved by the U.S.
Department of Transportation as configured by In-Situ Inc. and have
appropriate decals affixed. The containers are specifically sized and
fitted with high-density foam inserts to accommodate the most com-
mon combinations of instruments. Space is provided for a packet of
documents, computer software, and other necessary accessories.
•
2KPO.
Holds one HERMIT 2000 and one SE1004B field printer.
•
4XD.
Holds any four-reel combination of the following:
– Transducer with 400 ft. cable on ABS plastic reel
– 400 ft. extension cable on ABS plastic reel.
Appendix A: Accessories
Appendix A: Accessories
