OPERATION MANUAL
PREMIUM USB CAR POWER ADAPTER QC 5/9/12V
in-akustik GmbH & Co. KG
Untematten 12-14
79282 Ballrechten-Dottingen
GERMANY
Tel.: +49 (0) 7634 5610-70
Fax.: +49 (0) 7634 5610-80
E-Mail: info@in-akustik.com
Web: www.in-akustik.com
r
MADE IN
GERMANY
OPERATION MANUAL
AC-1502 | AC-1502-P6 | AC-2502-P8 | AC-2502-SF
GENERAL
Read, observe and adhere to the following safety instructions. Please keep the operating manual. Observe all the warning notices on the components and in the operating manual.
PROPER USE
•
This power cord / power bar may only be used for the connection of stationary HiFi and High-End consumer electronics devices that do not develop heat.
•
This power cord / power bar must only be used in dry areas.
•
Please also note the operating instructions of the devices you would like to connect.
General
•
All cables / power bars must be positioned in such a way that there is no danger of them being damaged (e.g. being stepped on, placed under furniture, fall of objects etc.).
•
Never kink, squeeze, pull over sharp edges or stress the power cord otherwise.
•
Make sure that no foreign objects or liquids enter the components.
•
Keep children and pets away. Spittle and bites can damage the insulation and may cause lethal electric shocks!
•
Never remove cables by pulling the cable; instead, always hold the plug when disconnecting.
•
Do not under any circumstances expose the components to high levels of humidity. Extreme temperature fluctuations, humidity and extended exposure to light can damage the components and alter their
appearance.
Humidity
Select an installation location for the components which does not have a high level of relative humidity and is free of moisture. Never use the components near water. Moisture can bypass the electrical insulation
and pose a lethal danger, as it can for all products not specially designed to be water-resistant. The components may not be exposed to dripping or sprayed water.
Positioning
Do not position the components near sources of heat, heaters, heating valves, ovens or other heat-producing devices. The components may only be stored and operated in the temperature range stated. The
components heat up during operation.
Connection
The power cord / power bar must only be connected to the maximal rated voltage! Check the power cord / power bar for possible damage before connecting.
Never use a damaged power cord / power bar! This must be repaired by a specialist or disposed of!
In stand-by mode, the components are not completely disconnected from the mains supply. To avoid any unnecessary hazards or energy consumption during longer absences, the components should be disconnec-
ted from the mains supply
Maintenance
Maintenance on the product may only be performed by persons qualified to do so. Maintenance is necessary in all cases of damage, i.e. in the case of damaged cables and plugs, as well as after liquid spills or
objects falling on the components, components falling down, foreign bodies entering the components, exposure of components to rain or humidity, or other influences impairing the functioning of the components
Looking after the product
Disconnect the components from the power supply before cleaning them Always clean the components with a soft, dry and lint-free cloth, or with a brush. Do not under any circumstances use scouring powder,
alcohol, benzine, furniture polish or similar substances.
USAGE OF POWER DISTRIBUTOR BARS
When using multiple power boards and extension cables, pay special attention to the DIN VDE 0100 part 420, para. 4.1 (risk of fire in electrical installations). Furthermore, the VDE 0100-410:2007-06 also
requires short breaks of 0.4 s for the TN system. The temperature of the cable may rise in such cases to the point of causing a fire. Therefore, the following applies to ALL power boards: Do not connect them in a
row and do not use if covered!
DESCRIPTION
Thank you for using this product.
Fundamentally, the output of a hi-fi system is nothing other than modulated household electricity. So this should get to the device with the minimum impediment. Extreme current peaks are the greatest challenge
for power cords and mains connection cables. They are caused by the connected devices as they convert alternating to direct current. These extreme current peaks cause a whole series of unwanted effects, which
is why the power cable is so important.
SAFETY INSTRUCTIONS
•
Check for damage before use!
•
Do not use with recognizable or suspected damage!
•
Use for stationary operated devices only!
•
Use for devices that do not develop heat only!
•
Use inside dry rooms only!
•
Never pull the cable!
•
Connect and disconnect by holding the plug only!
•
Protect from humidity and wetness!
•
Protect from heat and direct sunlight!
•
Keep away from small children and pets!
•
Do not kink, squeeze or otherwise strain!
•
Do not pull over sharp corners or edges!
•
Do not cover.
•
Do not open, repair yourself!
•
Do not modify!
01085D42
