Instruction when using Aquaceramic Processed products
- 7 -
TROUBLE SHOOTING GUIDE
Please use neutral detergents or normal-use detergents for families which is acidic or alkaline. But in order to remain long-lasting effect
of AQUACERAMIC, please
DO NOT
use the following detergents for ceramic because it will scratch the surface, glaze will be decayed.
- Detergent with polishing powder.
- Rubbing brushes with abrasion.
DO NOT
!
Note:
Do not let the detergent splash over areas, especially metal parts such as fixed set for S&C/toilet, stop valve, flexible hose hand
lever, button, etc… because it may cause of rust or damage.
Possible Cause
Problem
Poor flushing
action
Water won’t
stop running
Water supply
hose leaks
To Correct
Using this guide and referring to the accompanying instructions should help you solve most common problems encountered.
a. Water level in tank is below prescribe level.
b. Flush valve mechanism in tank closes too quickly or does not open.
c. Flush handle or button needs replacing.
d. Water pressure is too low.
e. Partially clogged trap way
and / or drainpipe.
f. Cleanser used in tank deposits residue.
g. No air vent.
a. Water level in tank is higher than overflow pipe.
b. Turn off the water supply if water continues to flow into the bowl until
the flush valve seat and / or rubber seal disk are worn or deformed.
c. Turn off the water supply valve if water continues to flow into the bowl
until the water level falls to the level of the overflow pipe, sand or debris
may be clogged in the water control mechanism.
d. Flush valve string is too tight, holding the flush valve open.
e. Button needs replacing
a. Improper installation.
b. Water pressure is too high.
a. Set to prescribed level.
b. Make sure there are no any material stuck to outlet components.
c. Replace.
d. Nomal water supply pressure must at least 20 psi.
e. Use a plunger or toilet augur to unclog.
f. Clean out tank and cease using the cleaser.
g. Install air vent per instructions.
a. Adjust the cylinder to maintain the water at the prescribed level.
b. Replace seat, rubber seal disk, or complete assembly, as needed.
c. Shut off water supply valve. Remove top cap of water control. Clean and
reassemble, or replace plunger.
d. Replace fulsh valve unit.
e. Replace button.
a. Reinstall, according to instructions.
b. Water pressure must not exceed 80 psi.
Detergents Industry
Polishing
Powder
Strong
alkaline
Strong
Acidic
Alkaline
Acidic
Neutral
Neutral detergents,
Soft brushes
brushes with abrasion
Detergent with
polishing powder, strong alkaline
& acidic,
Detergents for famillies
PRODUCT WARRANTY
If inspection of this product, within the warranty time after purchasing, confirms that its defective of a similar model under normal use in material or workmanship. We will repair or,
at its option exchange the product.
1. None any documentary evidences to show the period of warranty such as receipt, warranty card,.
2. Consequential or incidental damages.
3. Defects or damages arising from shipping, installation, alternation, accidents, misuse or lack of proper maintenance.
4. Postage or shipping costs incurred in returning products for repair or replacement under this warranty and any labor or other costs of removal or installation of products under this
warranty.
5. Discontinuous products.
LIXIL VIETNAM CORPORATION
Address: Yen Binh, Duong Xa, Gia Lam, Ha Noi, Vietnam
Website: www.inax.com.vn
SAFETY PRECAUTIONS
Read the instructions carefully before beginning.
Cautions and notes below if not complied may lead to serious
damange. Therefore, please follow strictly.
After finishing installation, check out whether the facility operates
properly or not. If possible, customer should to keep this instruction as
reference in the future.
* Before installation, please check the product
again for cracks or breaks during delivery
* Be sure to test operation and check for any breaks,
cracks after installation has been completed.
* Any cracks may cause injury, damage,
leakage or dirty the floor.
- Do not overtighten bolts.
Porcelain is subject to cracking, which may
cause injury to installing person or users.
ATTENTION
CARE AND MAINTERNANCE
Do not use haesh abrasives or caustic clean fixture surface. A mild detergent,
warm water ,and a soft cloth will remove normal dirt and soap accumulations
from fitting and surfaces.Rinse thoroughly after cleaning and polish with a soft
dry cloth to restore original luster of material
Notice:
Do not use cleaners in tanks. Products containing chlorine (calcium
hypochlorite) can seriously damage fitting in the tank. This damage can cause
leakage and poperty damage.
