background image

Set final base assembly

position

Loosen the (4) base clamping knobs and slide
the base assembly to locate the near side of the
base support panel at 36" from the saw blade.
See 

 .  Tighten the clamping knobs in

place.  Using a 

3

16

" hex tool, tighten the (4) set

screws through the holes located in the base
clamps.  Slide the (2) stop positioners up
against the base clamps as shown and tighten
the hex bolts.  Should you ever need to remove
the base assembly from your table saw, these
stop positioners will allow you to return to the
original setup in seconds.

6

Align base mount assembly

parallel to miter slot

Take the base mount assembly to the

table saw and as you lower the base mount
onto the rails, position the (4) clamping knob
assemblies directly under the slots in the base
clamps.  Slide the base assembly along the rails
to position the base support panel at 20" from
the miter slot, 

.  Take a measurement at

both ends of the panel.  Loosen the phillips
head screws that hold the base clamps as
necessary to align the panel parallel to the miter
slot.  Tighten the four base clamping knobs,
then tighten all eight screws that secure the
base clamps to the base support panel.
Replace the base support panel end caps.

FIG. 14

Set final base assembly position

Base clamp 

36"

First: Slide base assembly to

36" from saw blade and

tighten all (4) clamping knobs

3

16

" hex tool

INCRA TS III Owner’s Manual

7

5

FIG. 13

Align base mount assembly parallel to miter slot

Loosen base clamp

screws as necessary

Base clamp

Base support

panel

20"

Third: Tighten base clamping knobs

and all eight screws that secure the

base clamp to the support base

Miter slot

By loosening the (4) clamping 

knobs and set screws you can slide 

the base assembly to any position

along the length of the rails – great for
accessing a router table extension wing
placed to the left of the blade.

Replace

end caps

First: Lower base

assembly onto rails and

base clamping knobs

Second: Slide base

assembly to align base

support panel 20" from

and parallel to miter slot

Base

clamping knob

Third: Slide stop

positioners up to both

base clamps and

tighten hex bolts

Second: Tighten (4)

set screws through

holes in base clamps

Summary of Contents for TS III













Reviews: