Incra Twin Linear Owner'S Manual Download

Page: 20 / 20

Made in the U.S.A.

Taylor Design Group, Inc.

•

P.O. Box 810262

•

Dallas, TX 75381

INCRA is a registered trademark of Taylor Design Group, Inc.

0997

PARTS AND OPTIONAL ACCESSORIES

PRODUCT INFORMATION

For a product information update on the complete Incra line

of tools, please see your nearest dealer. If you are unable to

locate a store nearby, or if you have trouble finding a

particular product, we will honor your order directly.

For a product information brochure, call, write or fax to:

Taylor Design Group, Inc.

P.O. Box 810262, Dallas, TX 75381

Tel: (972) 418-4811 Fax: (972) 243-4277

Web Site: www.incra.com

WARRANTY

Taylor Design Group, Inc. warrants this product for one year from date of purchase. We will repair any defects due

to faulty material or workmanship, or at our option, replace the product free of charge. Please return the failing

component only, postage prepaid, along with a description of the problem to the address below. This warranty does

not apply to parts which have been subjected to improper use, alteration, or abuse.

LIFETIME WARRANTY ON POSITIONING RACKS

If an Incra positioning rack in this tool becomes damaged for ANY reason, Taylor Design Group will replace it free of

charge for as long as you own your tool. Return the damaged rack, postage prepaid, and allow 1 to 2 weeks for delivery.

NOTE:

Replacement parts cannot be sent unless damaged racks have been received by Taylor Design Group.

Part #

Part Description

Price

TL-CURSOR

Hairline Cursor (with mounting hardware)

$ 7.95

ISTOP

Stop Positioner (with mounting hardware)

$22.95

IEXT18

18" Stop Extender Bar with auxiliary stop, scale and hardware

$15.95

IJPT1

Incra Jig Projects & Techniques Book

$22.95

Features 14 original Incra projects, 4 exclusive new Incra joints,

and a wealth of tips and techniques that will help you master the Incra Jig

TL-SCALE16

16" long

⁄

" Lexan

floating scale

$ 2.95

TL-SCALE21

21" stainless steel primary scale

$ 9.95

TL-SCALE31

31" stainless steel primary scale

$14.95

Taylor Design Group, Inc.
P.O. Box 810262, Dallas, Texas 75381
Tel: (972) 242-9975 Fax: (972) 242-9985

www.incra.com

Summary of Contents for Twin Linear





















Search results

Summary of Contents for Twin Linear

Reviews:

Related manuals for Twin Linear

Brands by name

Popular brands

Incra Twin Linear, Owner'S Manual

Search results

Summary of Contents for Twin Linear

Reviews:

Related manuals for Twin Linear

Brands by name

Popular brands