Indesit BAAAN 40 FNF Series, Operating Instructions Manual

GB

51

1. Pull out the tray by pushing it up.
Check that the tray is ompletely empty and fill it with water through

the opening provided.

2. Take care not to exceed the level indicated (MAX WATER

LEVEL). Excess water prevents the ice cubes from dispensing
(if this happens, wait for the ice to melt and empty the tray).

3. Turn the tray 90°: due to the connected compartments each

mould fills with water (

see diagram

).

4. Close the opening with the lid provided and put the tray back.
5. When the ice has formed (minimum time approximately 8 hours)

knock the tray against a hard surface and wet the outside so
that the ice cubes come loose and take them out through the
opening.

WATER LEVEL

MAX

W

A

TER LEVEL

MAX

W

A

TER LEVEL

MAX

Start-up and use

Starting the appliance

!

 After transportation of the appliance, carefully place it in an upright

position and wait at least 3 hours before connecting it to the
electricity mains, to make sure it operates as it should.
• Clean the inside of the refrigerator well using warm water and

bicarbonate of soda before placing food inside it.

• The appliance comes with a motor protection control system

which makes the compressor start approximately 8 minutes
after being switched on. The compressor also starts each time
the power supply is cut off whether voluntarily or involuntarily
(blackout).

Freezer Compartment

When the product is switched on the freezer compartment is set to
its default value of -18°C. We recommend that the SUPER FREEZE
function is set (the freezer status bar continues to display the set
value) in order to accelerate the cooling process of the
compartment; when the inside of the compartment has reached its
optimal temperature the function will be deactivated and the food
may be placed inside.

Refrigerator Compartment

When the appliance is switched on the refrigerator compartment is
set to its default value of +5°C. We recommend that the SUPER
COOL function is set (the refrigerator status bar continues to
display the set value) in order to accelerate the cooling process of
the compartment. After a few hours it will be cool enough for food to
be placed inside.

Navigating the display

Setting the temperatures:

If the product is switched on, the refrigerator and freezer status
bars will indicate the temperatures set at that moment. To change
them, simply press the -  and + buttons corresponding to the
compartment for which you wish to change the set temperature.
More specifically, each time one of the buttons is pressed the
temperature is increased or decreased by 1°, and the level of cold
is adjusted accordingly.The temperature values that may be
selected for the refrigerator compartment are +12°C, +7°C, +6°C,
+5°C, +4°C, +3°C and +2°C, while the values that may be set for
the freezer are -18°C, -19°C, -120°C, -21°C, -22°C, -24°C and -
26°C.
The temperatures are automatically set to 

+5°C

 for the refrigerator

compartment and 

-18°C

 for the freezer compartment (these are

standard food storage values.
When the “

ECO

” function is active, the appliance automatically

adjusts the temperatures according to the conditions inside and
outside the refrigerator; the operation of this function is signalled by
the text “

AUTO

”.

Whenever it is necessary to activate the “

ECO

” function at

temperatures that are different to the standard storage values, the
“

ECO

” button must be pressed as soon as the function is activated

and held down while the new temperatures are set using the  -  and
+ buttons. Under these conditions, the temperatures may be set to
4°C, 5°C and 6°C for the refrigerator compartment and -18°C, -
19°C and -20°C for the freezer compartment.
When the 

HOLIDAY

 function is active the temperature may not be

adjusted, however the appliance adjusts itself automatically so that
the optimal settings for the situation are used: 

+12°C

 for the

refrigerator compartment and 

-18°C

 for the freezer compartment.

This function is indicated by the text “AUTO”.

To activate and deactivate the functions simply press the relevant
button and the function status will be signalled by the
corresponding LED switching on or off.
Several functions (

SUPER COOL, SUPER FREEZE, BOTTLE

CHILL, ECO

) are incompatible with others (

HOLIDAY

,...);

remember that there is a pre-set order of priority which will help you
to use the product in the best possible way.
When the BOTTLE CHILL function has finished, press the BOTTLE
CHILL button to stop the corresponding LED from flashing and to
silence the sound signal. This flashing and sound signal indicates
that the function is complete and that the bottle should be removed
from the freezer compartment.

Child Lock

In order to activate the Child Lock function, the Child Lock button
must be pressed for 2 seconds; the activation of the button lock is
confirmed by a short beep and the illumination of the
corresponding LED.
To deactivate the function, press the Child Lock button for 2
seconds; deactivation will be confirmed by a short beep and by the
corresponding LED switching off.

!

 The FREEZER status bar is also used to indicate an unusual

temperature increase in the freezer compartment (

see

Troubleshooting

).