Indesit WD 84 T, Instruction

The washer-dryer fails to
fill with water.

Is the hose correctly
connected to the tap?

Is there a water shortage ?

There could be work in
progress in your building or
street.

Is there sufficient water
pressure?

 The  autoclave

may be malfunctioning.

Is the tap filter clean?

 If the

water is very calcareous, or
if work has recently been
carried out on the water
piping, the tap filter could be
clogged with particles and
debris.

Is the rubber hose kinked?

The tract of the rubber hose
bringing water to washer-
dryer must be as straight as
possible. Make sure it is not
squashed or kinked.

The programme selector
knob keeps turning?

Wait a few minutes for the
drain pump to empty the
tub, 

switch the washer-dryer

off, select one of the symbols
stop/reset  , then switch it
back on. If the knob continues
to turn, call for assistance
because it is showing an
anomaly.

The washer-dryer
continuously fills and
drains water.

Is the drain hose positioned
too low? 

It must be installed

at a height ranging from 60 to
100 cm.

Is the end of the hose

immersed in water?

Does the wall drainage

system have a breather
pipe?

 If the problem persists

even after these checks, turn
the water supply off the
machine and call for
assistance.
If you live on an upper floor of
your building, there may be a
problem with your drain trap.
To solve this problem, a
special valve must be
installed.

Before calling, read the following

Troubleshooting

In most cases, when your washer-dryer fails to work, the problems arising can
be easily solved without  having to call for a technician. Before calling for
assistance, always check these points.

The washer-dryer fails to
start.

Is the plug correctly inserted
into the socket?

 It could have

been moved whilst cleaning.

Is there electricity in the
house?

A circuit breaker may have
switched off as a result of too
many electrical appliances
working at the same time. Or
maybe due to a general failure
in your entire area.

Is the washer-dryer door
closed properly?

For safety reasons, the
washer-dryer  cannot work if

the door is open or not shut
properly.

Is the On/Off button
pressed?

If it is, then a programmed start
has been set.

Is the programmed start
knob, in the correct position
for those models
concerned?

Is the water supply turned
on?

 For safety reasons, if the

washer-dryer  does not load
water, it cannot start a wash
cycle.

RIGHT

      WRONG

Turn off the water

supply after use.

This will eliminate

the possibility of

leakage.

Always leave the

appliance door ajar

to avoid bad odours.

Clean the

appliance’s

exteriors gently.

To clean the

exteriors and the

rubber parts of the

appliance, always

use a soft cloth

dipped in warm and

soapy water.

Leave the washer-dryer

plugged in while

cleaning.

Even during maintenance,

the appliance should

always be unplugged.

Use solvents and

aggressive abrasives.

Never use solvents or

abrasives to clean the

external and rubber parts

of the washer-dryer.

Neglect the detergent

dispenser.

It is removable and can

easily be cleaned by

leaving it under running

water.

Go on holiday without

thinking about her.

Before leaving, always

make sure that the

washer-dryer is

unplugged and that the

water supply is turned off.

9

Instructions for installation and use

Simple: with the new Indesit technology,  you need less than

half of it, to get good results on twice as much!

This is why you cannot see the water through the door:

because there is little, very little of it, to respect the

environment yet without renouncing maximum cleanliness.

And, on top of that, you are also saving electricity.

But where did all the water go?