GB
Personalisations
C
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature
(see Programme table on page 6)
.
The temperature can be lowered, or even set to a cold wash ( ).
Set the drying cycle
Turn the DRYING knob to set the desired drying type.
Two options are available:
A
- Based on time: From 40 minutes to 180.
B
- Based on the damp level of the dry clothes:
Iron
: slightly damp clothes, easy to iron.
Hanger
: dry clothes to put away.
Cupboard
: very dry clothes, recommended for towelling
and bathrobes.
A cooling stage is foreseen at the end of the drying cycle.
If your laundry load to wash and dry is exceptionally in excess
of the maximum load foreseen
(see table opposite)
, perform
the wash cycle, and when the programme is complete, divide up the garments and put part of them back in the
drum. Now follow the instructions provided for a
dry only
cycle. Repeat this procedure for the remainder of the load.
Dry only
Turn the PROGRAMME knob to one of the drying settings (7-8) depending on the type of fabric, then select the
desired drying type using the DRYING knob.
Important:
- A spin cycle is carried out during the drying if you have set a cotton programme and a level of
dryness (Cupboard
, Hanger
, Iron
).
- For cotton loads of less than 1 Kg, use the drying programme designed for delicate fabrics.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
Fabric
type
Load type
Max.
load
(kg)
Cup-
board
Hanger
Iron
Cotton,
Linen
Clothing of different sizes
5
180
170
140
Cotton
Terry towels
5
180
170
140
Terital,
Cotton
Sheets, Shirts
2,5
140
120
100
Acrylics
Pyjamas, socks, etc.
1
70
65
60
Nylon
Slips, tights, stockings, etc.
1
70
65
60
Table of drying times
The data contained in the
table are purely indicative.
Fu n c tion
E ffe c t
C om m e n ts
E na b le d with
p rogra m m e s:
D e la y
Tim e r
D elays th e s tart
o f th e w as h by
up to 9 h o urs .
P res s th e butto n rep eated ly un til th e L ED co rres p o n d in g to th e
d es ired delay is tu rn ed o n .
T h e fifth tim e th e b utto n is p res s ed , th e fun ctio n w ill be d is ab led .
N .B .: O n ce yo u h ave p res s ed th e S tart/R es et b utto n , th e d elay
can o n ly b e d ecreas ed if yo u w is h to m o d ify it.
A ll
E a sy iron
T h is o p tio n
reduces th e
am o un t o f
creas in g o n
fab rics , m akin g
th em eas ier to
iro n .
W h en th is fun ctio n is s et, p ro g ram m es 4 , 6 w ill en d w ith th e
laun d ry left to s o ak (A n ti-creas e) an d th e R in s e cycle ph as e
L ED w ill flas h .
- to co n clud e th e cycle, p res s th e S TA R T /R ES ET b utto n ;
- to run th e d rain in g cycle alo n e, s et th e kn o b to th e relative
s ym bo l an d p res s th e S TA R T /R ES ET b utto n .
T h is fun ctio n is in co m patib le w ith th e S TA IN R EM O VA L fu n ctio n .
If yo u als o w an t to ru n th e dryin g cycle, th is b u tto n is en abled
o n ly if co m bin ed w ith level (
Iron
).
3 , 4 , 6 ,
9 , 1 0 ,
R in se c yc le .
E x tra
R in se
In creas es th e
efficien cy o f th e
rin s e.
R eco m m en d ed w h en th e app lian ce h as a full lo ad o r w ith larg e
quan tities o f d eterg en t.
1 , 2 , 3 , 4 , 9 ,
1 0 , 1 2 , 1 3 ,
R in se c yc le .
1 2 0 0-6 0 0
R ed uces th e
s p in s peed .
All
programmes
except for 6, 7,
8 and draining.
