background image

 

01.05.2014 (release date and version)  

_________________________________________________________________________________ 
FB TS AS7 01                    ICG® Standard Operating Procedure | released by ICG® Service Department                                                                   9 

 

4)    Handlebar assembly 

       a)  Bring handlebar to its maximum vertical position. Do not remove warning tape on slider prior 

to handlebar is mounted to the upper slider. 

       b)    

ATTENTION!

 

Place the flat handlebar support under the console bracket as shown on the          

               

picture. 

               Mount handlebar weldment using the M8 x 25 x 1.0P counter sunk hex. socket bolt from   
               beneath using a straight shaft (round head) 6mm Allen key socket wrench. 
 

 Maximum torque: 25-30 Nm. 

       c)     Mount the plastic end cap on the lower handlebar slider and check the horizontal and  
 

 vertical adjustment as described in the separate SOP (FB TS HB7 01). 

                       

  

                                           a)                                                                                   b) 

                      

 

                                                                                                         c) 

Summary of Contents for TOMAHAWK IC5
















Reviews: