55/142
AB Industrietechnik srl – Via Julius Durst, 70 – 39042 BRESSANONE (BZ) Italy – Tel: +39 0472/830626 – info@industrietechnik.it – www.industrietechnik.it
16. Zone display or alternate zones on the display:
7KHRSHUDWLQJVHWSRLQWPD\EHGLVSOD\HGIRUDVSHFL¿F]RQHVHWWLQJWKHSDUDPHWHU
I72
(display A) or
I73
(display B) to 10
(zone 1) or 11 (zone 2) or 12 (zone 3) or 13 (zone 4). In this case, in heating mode, the value corresponding to
WHS
is dis-
played, in cooling mode the value corresponding to
WCS
is displayed.
7RYLHZWKHRSHUDWLQJWHPSHUDWXUHIRUDVSHFL¿F]RQHRQ
display A, set parameter I72 to 4 (zone 1) or 5 (zone 2) or 6 (zone 3)
RU]RQHȉKHQXPEHURIWKHFRUUHVSRQGLQJ]RQHDQGWKHLFRQVUHODWHGWRWKHRSHUDWLRQRIWKDW]RQHDUHGLVSOD\HGRQ
display C.
By setting
I72
, related to display A, to 8 (or 14), all operating temperatures (or operating setpoints) of the zones will be alter-
nately displayed. The zone corresponding to the operating temperature (or operating setpoint) is indicated on display C and
changes every 10 seconds. The indicated icons are related to the operation corresponding to the zone indicated by display C.
If
I72
is set to a value different than 4, 5, 6, 7, 8, 10, 11, 12, 13, 14 the icons regarding the operation of the various areas will
be disabled. If there are more thermal actuators per zone, the alternate display will refer to the thermal actuators, not to the
zones. In this case, display C shows the number corresponding to the thermal actuator.
Note: For the SLAVE_X controller, if
I72
=8 and
I73
LIWKHÀRRUWHPSHUDWXUHFRQWUROIXQFWLRQZLWKFRQWUROVHQVRUH[FOXVLRQ
is enabled (see
³&RQWUROZLWKÀRRUWHPSHUDWXUHFRQWURO´SDJH
52
, the display shows:
Display_A
Display_B
Heating
ÀRRUWHPSHUDWXUHVHQVRU
I41
PLQLPXPÀRRUWHPSHUDWXUH
Cooling
ÀRRUWHPSHUDWXUHVHQVRU
98.0°C (209.0°F) *
* the setpoint is forced at a high value to avoid any start-up of the thermal actuator.
Note: Setting parameter
I72
(related to display A) at a value different than 4, 5, 6, 7, 8, 10, 11, 12, 13, 14 will not allow the
display of the icons regarding the operation of the corresponding zone. By setting parameter
I73
to 8 or 14, the operating
temperatures or the operating setpoints will not be displayed alternately, unless on display A the alternate display of operating
zones (
I72
=8 or
I72
=14) is enabled
,IQRFRQWDFWVDUHFRQ¿JXUHGLQ³QRQRFFXSLHGKROLGD\´RU³HQHUJ\VDYLQJ´PRGHDQGLIWKHRSHUDWLQJPRGHKDVEHHQVHWPDQ
-
XDOO\ZLWKWLPHVORWVWKURXJKTXLFNDFFHVVSDUDPHWHUVĺVHH
³02'(EXWWRQIXQFWLRQ´SDJH
22
) and the time slots function
I78
=0, then within the time slot it is controlled with the base setpoint. In this case, next to “display C” (see
³'LVSOD\NH\SDG
DQGLFRQV´SDJH
7
), the text
ON
is displayed and icon
will be enabled.
20.3
1
Outside the time slots, the economy mode is controlled and next to “display C” (see
³'LVSOD\NH\SDGDQGLFRQV´SDJH
7
)
the
OFF
text will be displayed and icons
and
ECO
will be enabled.
20.3
1
2WKHUZLVHWKHFRQWDFWFRQ¿JXUHGLQ³QRQRFFXSLHGKROLGD\´RU³HQHUJ\VDYLQJ´PRGHKDVSULRULW\RYHUWLPHUVORWVZKLFKDUH
not considered (
FH-xxCSH1
models).
,IRQHRIWKHFRQWDFWVLVFRQ¿JXUHGLQ³QRQRFFXSLHGKROLGD\´RU³HQHUJ\VDYLQJ´PRGHDQGLIWKHRSHUDWLQJPRGHLVLQKROLGD\
PRGHPDQXDOO\VHOHFWHGWKURXJKTXLFNDFFHVVSDUDPHWHUVĺVHH
³02'(EXWWRQIXQFWLRQ´SDJH
22
), control is done based
RQFRQWDFWVHWWLQJ7KHFRQWDFWFRQ¿JXUHGLQWKH³QRQRFFXSLHGKROLGD\´RU³HQHUJ\VDYLQJ´PRGHKDVSULRULW\RYHUWKHPDQXDO
FRQ¿JXUDWLRQ,IWKHIXQFWLRQ³QRQRFFXSLHGKROLGD\´LVDFWLYHLFRQ
is enabled.
When timer extension mode is activated manually, it takes priority over energy saving, holiday (see
“Timer extension or forced
SUHVHQFH PRGHV´ SDJH
60
) and timer slots modes (models
FH-xxCSH1
). During the timer extension period, the icon
ÀDVKHV
