LED
_
+
12V
battery
Ch.2
Ch. 3
Ch.1
Ch. 4
Installation manual and technical specification
G1
- radio receiver socket,
D4
- light emitting diode,
PR3, PR4
- channel 1 and channel 2 relays
1, 2
- channel 1 and channel 2 relay terminals,
24V DC
- non-stabilised 24 V DC/AC power supply,
12V DC
- stabilised 12 V DC power supply,
SW1
- code learn key
SW2
- code reset key
ORS-X2T DECODER SPECIFICATIONS
Supply voltage
24 V/DC/AC or 12 V
DC,
Power input
10 mA (stand-by),
Operating frequency
435 MHz,
Antenna input impedance
50
,
Number of channels
2
Range
>>100 m
DECODER OPERATION
The ORS-X2T remote control decoder with a built-in radio receiver allows control of two individual devices. The decoder outputs
include two pairs of terminals connected to the contacts of individual relays. The decoder is compatible with two or four-channel
remote controls. Press the remote control key to close the contacts of a specific relay; the contacts are closed for as long as the
remote control keys are pressed. The contacts are opened approx. 1 second after the key is released. Pressing both remote control
keys will not activate the decoder. For four-channel remote controls, channel 1 and channel 2 keys control PR3 and PR4 relays.
Replacing jumper I and II will allow relay control with channel 3 and channel 4 keys. It allows operation of two decoders, i.e. four
independent devices with a single remote control.
DECODER POWER SUPPLY
The decoder can be supplied with a direct or alternating non-stabilised or stabilised 24 V voltage or direct 12 V voltage.
REGISTERING THE REMOTE CONTROLS
The decoder can learn and store up to
255
(two hundred fifty five) different remote controls. Press and hold
SW1
(learn 1-2) to
register a new remote control to the decoder.
The
L5
LED goes on for approx. 1 second. Press any key on the remote control to be
register. The
L5
LED will go on and off. The remote control is registered to the decoder.
RESETTING REMOTE CONTROL CODES
All registered remote controls can be removed from the memory. Press and hold
SW1
then press
SW2
on the decoder, release
SW1
and
SW2
after approx. 2 seconds. All remote control codes will be removed and the same or different remote controls can be
registered.
PIL – 04XT, PIL-04XB
REMOTE CONTROL TRANSMITTER
REMOTE CONTROL TRANSMITTER SPECIFICATIONS
Supply voltage
12 V DC (A23 battery)
Operating frequency 435 MHz
Number of channels· 4
The PIL-04XT/PIL-04XB is a four-channel remote control, where each key generates different code to
control different channels.
The remote control generates dynamic (rolling) codes and each generated code is different. The code
that has already been used will not be received by the decoder. A serial number, different for each remote
control and assigned at the production stage is part of the generated code.
NOTES ON RECEIVER INSTALLATION
The decoder features a high sensitivity built-in radio receiver. Each product is individually tested and guarantees a range of
approx. 200 m in an unobstructed area. After the decoder is installed, and before connecting other devices, check its range and
correct operation. The keys can be pressed not often than once per second. Pressing the keys too often will not cause the control
unit to switch to the next phase, i.e. it will not execute the next command. In case of any issues with the range or correct operation,
measure the power supply voltage. A minimum voltage to guarantee correct operation and range is 24 V AC/DC or 12 V DC. If the
range is insufficient with a correct supply voltage, change the radio receiver location.
Limited range may be caused by:
1.
The receiver positioned too low (an optimum height is 2-3 metres above the transmitter level).
2.
The receiver too close to a large metal object.
3.
The receiver obstructed by the metal sheets, metal structures etc.
The range can be improved by changing the transmitter location. Connect the decoder with suitable range only. Please allow
for the device lag of approx. 0.5 second between the key is pressed and the relay is activated.
