P. I. E. INEL Sp. z o. o., ul. Mostowa 1, 80-778 Gdańsk, inel@inel.gda.pl www.inel.gda.pl
2.3
“Electrical connections
DISCONNECT POWER SUPPLY BEFORE MAKING
ANY CONNECTIONS!
Improper roller blind installation will cause the
motor to stop unexpectedly.
In order for the obstacle detection drive to function properly,
the following is required:
1. Use a special driver provided with the motor (diagram 2-E)
2. Ensure that the curtain can move freely in the guides and
the cassette. This movement may not be obstructed (e.g.
by increase of the roller blind cassette temperature,
mosquito net etc.)
3.
PROGRAMMING
WARNING:
The drive is initially in factory mode which does not
allow the programming of limit positions. In order to set limit
positions you must switch into programming mode by using
service cable or blind switch.
In the factory mode and during limit position set-up the drive
will move with a 1-second pause immediately after start - this
means that no limit positions have been set.
BEFORE PROGRAMMING
A. Check whether the direction of roller blind movement is
consistent with the switch directional buttons (if they are
opposite, switch around the wires on the switch).
B. Place the lower edge of the curtain at half the height of
the guides. Starting the programming procedure too near
the roller blind cassette may damage it.
ENTERING PROGRAMMING MODE
3.1 With a service cable
When using a service cable, press and hold the
and
buttons at the same time for at least 3 seconds. The
roller blind will confirm by moving up-down-up-down.
OR
3.2 With a blind switch
Press the buttons of the switch in the following order,
making the roller blind perform a short move each time:
↓
↓
↑
↓
↑
↑
↑
The presses should not be longer than 1 second counted
from the start of movement. The last press will confirm
the entered sequence - it should last at least 2 seconds.
The roller blind will confirm the start of programming by
moving up-down-up-down.
WARNING! Programming always starts with the set-up of
the upper limit.
AUTOMATIC LIMIT PROGRAMMING
The
programming
procedure
may
be
performed
automatically only if blocking hangers and stoppers are
used. The window must be fitted with a sill. The length of
the curtain must be adjusted to the length of the guides.
1. Press and hold the "
↑
" button for the duration of the
entire programming procedure.
2. The drive will stop on stoppers, after 3 seconds it will
set the upper limit and then switch the movement
direction. At the bottom the drive will stop as soon as
it reaches the sill and set the lower limit, after which it
will return to the upper limit and confirm that
programming is finished.
When using a service cable, the entire programming may
be performed by setting the switch
to
'I'
.
WARNING! Releasing the button during automatic
programming will automatically enter the SEMI-
AUTOMATIC programming mode.
SEMI-AUTOMATIC LIMIT PROGRAMMING
UPPER LIMIT
Upper limit in the desired position (if no stoppers are
present):
a. Press and hold the "
↑
" button.
b. Release the button in the desired upper limit
position. Fine tune the position by short pressing the
"
↑
" or "
↓
" buttons.
c. Press and hold the "
↓
" to confirm the upper limit.
The roller blind will make a short movement, and
then confirm that the upper limit position has been
saved by two down-up sequences. It will then start
moving down. At this point release the button and
start programming the lower limit.
OR
Upper limit by overload (if stoppers are used):
Before
drive
startup/programming
check
the
condition of the curtain, guides and roller blind
cassette and whether there is a sill mounted in the
window!
The roller blind cassette and guides should be free from any
contaminants and ensure unrestricted curtain movement
throughout the entire length. If the guides are contaminated
with building materials or are too tight, they can cause
damage to the drive and the roller blind, which is not
covered by the warranty.
N - neutral
PE - protective
L - phase
black
yellow-green
grey
–
not used
blue
brown
Figure 3
Figure 4