THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT ANCHORAGE POINT IN THE CAR. REFER TO CAR OWNER’S
HANDBOOK FOR LOCATION OF ANCORAGE POINTS. REMOVE THE THREAD PLUG AND INSTALL THE ATTACHMENT BOLT
AS SHOWN IN FIGURE 1A & 1B. REFER TO A CHILD RESTRAINT FITTING STATION IF NO ANCHORAGE POINTS ARE IN THE MOTOR CAR.
CAUTION: DO NOT OVERTIGHTEN ANCHOR
BOLT. MAXIMUM TORQUE FORCE IS 20NM.
OVERTIGHTENING MAY SNAP BOLT
WARNING: If A.D.R. anchorage point is recessed,
spacer(s) may be required. Spacer Part No’s are as
follows: 10mm - CCS001;
5mm - CCS002
FOR SEDANS ONLY
Drill a 9mm diameter hole in the parcel shelf on the centre
line of the seating position as shown in Figure 1D. Hole
must be no closer than 200mm from the front of the back
seat. Install the anchor bolt as shown in Figure 1C.
In New Zealand consult the agent of the vehicle.
WARNING: CHILD RESTRAINTS MUST NOT BE ATTACHED TO UNSOUND
METAL OR WOOD OR SYNTHETIC STRUCTURES. WHEN DRILLING THE 9MM
HOLE DO NOT DRILL THROUGH FUEL LINES, FUEL TANKS, ELECTRICAL
WIRING OR RADIO SPEAKERS. WEBBING STRAPS MUST BE PROTECTED
FROM SHARP CORNERS AND EDGES.
THE ANCHOR FITTING MUST BE USED ONLY AS DESCRIBED ABOVE. IT
MUST NOT BE HOOKED ONTO ANY OTHER OBJECT.
The shaded areas show some of the
possible locations of the anchor fitting.
With each shaded area is an anchor
fitting showing the correct way to install
the fitting. The anchor fitting should be
aligned as shown unless stated otherwise
in the vehicle owner’s handbook.
Front of
Vehicle
If anchor point is less than
80mm from seat, install in
this position.
anchor point
CENTRE LINE OF
SEATING POSITION
FOR VEHICLES FITTED WITH ANCHORAGE POINTS.
FOR VEHICLES NOT FITTED WITH ANCHORAGE POINTS
HOW TO INSTALL ANCHORAGE FITTINGS
2
Note to Queensland purchasers:
The installation of anchorage
points
must be approved
by authorised officers appointed by
Queensland Transport. Authorised officers can be sourced from all
Queensland Transport Customer Service and Queensland Ambulance
Service Centres.
ATTACHMENT BOLT
FRONT OF VEHICLE
ANCHOR FITTING
ATTACHMENT BOLT
FOR VEHICLES OTHER THAN SEDANS
In Australia, consult your nearest child restraint fitting station or
traffic authority for vehicle inspection to find the best, correct
position for the placement of the anchorage point, and for the
correct attachment bolt length and use of spacers.
FRONT OF
VEHICLE
Step 1: Do step 1 to 3 from “to change the shoulder slot height” on page 6.
Step 2: Disengage the buckle and tongues. Push the buckle through the crotch slot in the cover. Pull the
cover up and through the shoulder strap webbing and buckle tongues. Do NOT remove the harness
from under the seat.
Step 3: Once cover is removed, “click” the buckle tongue back into the buckle for safe keeping.
TO REMOVE COVER
7
Step 1:
Disengage buckle tongues from the buckle.
Step 2:
Feed shoulder strap webbing and buckle tongues through the thigh slot holes in the cover.
Step 3:
Feed buckle through the crotch slot hole of the cover.
Step 4:
Do steps 4 & 5 from “to change the shoulder slot height” on page 6.
TO REPLACE COVER
Step 1:
Slide the harness shoulder straps out through
the gates in the metal spreader plate. Pull the
harness shoulder straps through the shoulder
slots to the front of the restraint.
Step 2:
Disengage buckle tongues from the buckle.
Step 3:
Pass the three bar slide located below the
thigh harness slots on the end of each body/
shoulder straps through the thigh harness
slots. Each side of harness is now removed.
Step 4:
To release the buckle / crotch strap pass the
three bar slides attached through the crotch
slot holes in seat section.
TO REMOVE HARNESS
Step 1:
Place one end of one of the harnesses through
the required shoulder slot hole (see arrow 1 in
Figure 16) and connect to the metal spreader
plate by passing the webbing through the
“gate” (see arrow 2 in figure 16)
Step 2:
Feed the other end of the harness and the three
bar slide through the thigh slot (see arrows 3 in
figure 16)
Step 3:
Connect the buckle/crotch strap by feeding
the three bar slides on the crotch strap through
the holes in seat section.
Step 4:
Connect the other side of the harness as
shown in figure 16 and Steps 1- 2 above
Step 5:
Engage the buckle tongues in the buckle.
TO REPLACE HARNESS
SHOULDER SLOTS
HARNESS
SHOULDER
STRAPS
THIGH HARNESS
SLOTS
THREE BAR
SLIDES
METAL
SPREADER
PLATE
BUCKLE
TONGUES
BUCKLE
CROTCH STRAP
WITH THREE
BAR SLIDES
Figure 15
Figure 16
SHOULDER SLOTS
METAL
SPREADER
PLATE
THIGH SLOT
BUCKLE
TONGUES
(1)
(2)
(3)
