background image

Information

S E C T I O N

Child Car Seat

WITH INBUILT HARNESS

This instruction manual covers various models under the Model number CS9013 design. 
These child restraints are installed in the rear of the car and can only be used forward-facing. 
They are installed in the car using the car seatbelt and the top tether strap attached to the car’s 
child restraint anchor fitting. This Car Seat is designed to be used by children from approxi-
mately 6 months of age up to approximately 8 years of age.

Air Cocoon Technology™ - A Protective Embrace

Air Cocoon Technology™ (A.C.T.) enhances 
protection by dramatically reducing the impact forces 
during a crash. A.C.T. utilises a layer of air held inside 
the entirety of the child restraint shell, offering an 
increased level of protection across the entire surface 
area of the restraint. Your child is quite literally 
cradled in a cocoon of air, offering a true 180 degrees 
of protection to your child's vital organs.

Air Cocoon Technology™ integrated child restraints 
start their life as an actual pillow of air. This pillow is 
moulded into a child restraint, retaining the pillow-like 
construction while adding incredible strength and 
structural integrity. This manufacturing process is 
called blow-moulding. Air Cocoon Technology™ 
(A.C.T.) is an encompassingly protective ‘cocoon’ 
around your child.

Twist & Lift™ 

This Child restraint has also been designed with 
‘TWIST & LIFT” which features deep side wings that 
shield and contain your child’s head in a side impact 
crash. The TWIST & LIFT system is designed to be 
adjusted as your child grows which automatically 
repositions the harness at the same time.

No child restraint can guarantee absolute protection 
from injury in every crash. However, to ensure that 
your child gets all the protection designed into the 
restraint please read and follow the instructions 
exactly and use only InfaSecure recommended parts 
and accessories.

InfaSecure is an Australian owned and operated 
family business, which can trace it's roots back over 
60 years, becoming the single largest Australian 
owned and operated child restraint company in the 
country. Today, we are still growing, continuing to 
innovate and providing high quality products at an 
affordable price.

AUSTRALIAN

DESIGNED &

FAMILY OWNED

2

Summary of Contents for CS9013





































Reviews: