background image

UPPER ANCHORAGE FITTINGS

Attachment
Bolt

THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT ANCHORAGE POINT IN THE CAR.
LOCATE THE ANCHORAGE POINT BEHIND THE REAR SEATING POSITION
CONSULT THE CAR OWNER’S HANDBOOK FOR LOCATION OF ANCHORAGE POINTS.
REMOVE THE THREAD PLUG FROM THE PARCEL SHELF/FLOOR/ROOF AND INSTALL THE ATTACHMENT 
BOLT AS SHOWN IN FIGURE 1A & 1B.

CAUTION: DO NOT OVERTIGHTEN ATTACHMENT 
BOLT. MAXIMUM TORQUE IS 20NM.

Some vehicles may have an anchor fitting already 
fitted by the vehicle manufacturer.

If no anchorage points can be found refer to 
the vehicle manufacturer, or an authorised child 
restraint fitting station for the best location of an 
anchorage point.

Refer to the vehicle owners handbook or child 
restraint fitting station for the possible use of 
spacers.

Some vehicles may require the use of additional 
extension straps (not supplied with this child 
restraint)

If so ring InfaSecure on (Aust) (02) 4728 8080 for 
nearest supply location.
ADDITIONAL EXTENSION STRAPS AVAILABLE:
CS111 300mm Extension strap
CS112 600mm Extension strap
CS113 200 - 900mm Adjustable Extension strap

Anchorage Fittings

WARNING: If A.D.R. anchorage point 
is recessed, spacer(s) may be required. 
Spacer Part No’s are as follows: 
10mm - CCS001;
5mm - 

CCS002

r

Top tether strap and attachment clip

  must always be used

r

Always ensure that the upper attachment clip

  is correctly engaged to the anchor fitting

r

THIS RESTRAINT MUST BE ATTACHED TO 

  A CHILD RESTRAINT ANCHORAGE POINT 
  IN THE CAR. REFER TO CAR OWNER’S 
  HANDBOOK FOR LOCATION OF  

 

  ANCHORAGE POINTS. REFER TO A CHILD  
  RESTRAINT FITTING STATION IF NO CAR  
  ANCHORAGE POINTS ARE IN THE MOTOR CAR.

r

THIS RESTRAINT IS NOT SUITABLE FOR 

  USE WHERE TOP TETHER STRAP MAY
  FALL INTO A SPLIT IN THE SEAT BACK OR 
  OFF THE SIDE OF THE SEAT.

The shaded areas show some of the 
possible locations of the anchor fitting. 
With each shaded area is an anchor 
fitting showing the correct way to install 
the fitting. The anchor fitting shoud be 
aligned as shown unless stated otherwise 
in the vehicle owner’s handbook.

 

For cars fitted with a child restraint anchorage point

Front of 
Vehicle

If anchor point is less 
than 80mm from seat, 
install in this position.

Lock 
Washer

Anchor
Fitting

Front of Vehicle

Spacer(s)
(if required)

Vehicle Trim

Vehicle Metal
Structure

 

WARNINGS

!

32

Summary of Contents for CS9013





































Reviews: